Bedienungsanleitung MTD CubCadet serie 6000 (Seite 23 von 25) (Englisch)

507839

Zoom out

Zoom in

Vorherige Seite

1/25

Nächste Seite

English User manual

Exchanging the headlight

bulbs

 Open the engine bonnet.

 On the bulb unit (a), remove the

cable (b).

 Turn the bulb unit to the left by a

quarter of a revolution and

remove from the reflector (c).

 Exchange the bulb with a bulb of

the same wattage.

 Replace the bulb unit into the

reflector and secure it (by turning

a quarter of a revolution to the

right).

 Mount the cable on the bulb unit.

 Close the engine bonnet. Check

that it is fully engaged.

Exchanging the tail light bulbs

 Turn the bulb mounting anti-

clockwise until the tounges on the

mounting oppose the notches in

the tail light reflector.

 After bringing into line, carefully

pull the mounting out of the tail

light reflector.

 Remove the bulb from the

mounting and replace it with

a new one.

 Bring the tounges on the

mounting into line with the

notches in the reflector and

carefully push the mounting into

place. Tightly turn the mounting in

a clockwise direction.

Exchanging the indicator

bulbs

 Loosen the screws on the lens

and remove the lens.

 In order to remove the bulb from

the lamp mounting, press the

bulb in a little and turn it anti-

clockwise.

 Align the new bulb on the

mounting slot, press the bulb into

the mounting and screw it into the

mounting in a clockwise direction.

 Secure the lens again using the

screws.

Exchanging the fuses

The tractor’s electric system is

protected from high current damage

with fuses. Always replace fuses

with those of the same amperage.

If the electric system does not work,

check for fuses which have been

tripped.

If the electrical system regularly trips,

take it to a specialist workshop.

Fuses in the cable trunk

The fuses in the tractor cable (3)

trunk protect the entire electrical

system of the tractor.

A defective fuse is exchanged as

follows:

 Open the bonnet and remove the

right side covering

 In front of the cross-sheet,

localise the fuse holder (1) directly

on the right hand side, on the

inner side of the instrument

holder.

 Remove the fuse (2) from the

holder and replace it with one of

the same amperage. NEVER

replace it with one of a higher

amperage.

 Attach the side covering and

reclose the bonnet.

Tyre pressure

t~êåáåÖ

kÉîÉê=ÉñÅÉÉÇ=íÜÉ=ã~ñáãìã=

éÉêãáííÉÇ=íóêÉ=éêÉëëìêÉ=EëÉÉ=ëáÇÉ=çÑ=

íóêÉFK=tÜÉå=éìãéáåÖ=ìé=íÜÉ=íóêÉëI=

Çç=åçí=ëí~åÇ=áå=Ñêçåí=çê=~ÄçîÉ=íÜÉãK

The recommended tyre operating

pressure is:

For tyre equipment suitable for

lawns:

Over-inflating reduces the longevity

of the tyres. Tyre pressure should be

checked before every journey.

Notes concerning wheel

change

t~êåáåÖ

låäó=ìëÉ=~ééêçîÉÇ=îÉÜáÅäÉ=à~ÅâëK=

Work safely. Only tighten the screws

/ nuts crosswise using a torque key.

The starting torque for the screws /

nuts:

– Front wheels 74 Nm

– Rear wheels 108 Nm

Dimension

Tyre

pressure

front 23 x 9.5 – 12 0,7 bar

(0,8 max.)

rear 31 x 12 – 15 1.0 bar

(1.3 max.)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

MTD CubCadet serie 6000 Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von MTD CubCadet serie 6000

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info