Bedienungsanleitung MTD CubCadet serie 6000 (Seite 21 von 25) (Englisch)

507839

Zoom out

Zoom in

Vorherige Seite

1/25

Nächste Seite

English User manual

 Attach the oil-fill lid to the

supports and turn clockwise until

it sits securely. Replace the

dipstick inserting it firmly into the

measuring tube.

Important note

The oil-fill lid and dipstick must always

sit securely when the engine is

running. If this is not done, servere

damage can be done to the engine.

Inspecting/topping-up crank

and hydraulics oil

The oil level in the hydrostatic cranks

/in the hydraulics system should be

inspected after every 50 hours of

operation. Only inspect the oil level

after the engine has come to a stand

and the tractor is on a level surface.

The oil-fill lid/oil dipstick (1) is located

at the rear end of the tractor, above

the rear PTO covering (2).



Keep the area surrounding the oil-

fill lid/oil dipstick clean so that no

dirt can get into the crank

mechanism.



Take the dipstick out, wipe it, insert

it again and screw it in completely.

In order to read the oil level,

unscrew and take it out. Always

keep the oil level between the MAX

(3) and MIN (4) marks.



If the oil level is too low, top it up

with hydraulic oil. Loosely place a

funnel into the supports such that

the funnel pipe has enough space

and that no accumulation of air

forms when filling. ONLY fill to the

MAX (3) mark, never higher.

Note

As stated in the lubricating table,

always use the hydraulic oil which is

best suited to this tractor. Other oils

can impair performance and damage

the crank mechanism.

 Insert the oil-fill lid/oil dipstick into

the crank housing and turn

clockwise until it fits securely.

Check the oil level in the front

axle and the wheel

transmission

Inspect the oil level on the front axle

and in the wheel transmission after

every 50 hours of operation.

Only inspect the oil level after the

engine has come to a stand and the

tractor is on a level surface.

Inspect oil on the front axle

The oil-fill lid/oil dipstick (1) is located

on the=äÉÑí=Ü~åÇ=ëáÇÉ=of the axle

housing (2).

 Keep the area surrounding the oil-

fill lid/oil dipstick clean so that no

dirt can get into the axle housing.

 To remove, turn the oil-fill lid/oil

dipstick in an anti-clockwise

direction.

 Take the dipstick out, wipe it,

insert it again and screw it in

completely. In order to read the oil

level, unscrew and take it out.

Always keep the oil level between

the MAX (3) and MIN (4) marks.

 If the oil-level is too low, only top it

up with as much lubricating oil so

that the MAX mark is reached on

the dipstick. NEVER fill too much

oil into the axle housing.

 Insert the oil-fill lid/oil dipstick into

the axle housing and and turn

clockwise until it fits securely.

Inspect the oil in the wheel

transmission

Inspect the oil-level at the supports

of the two wheel transmission

mechanisms.

 The filling supports (2) are located

a little way above the wheel hub

on the front side of the êáÖÜí and

äÉÑí wheel transmission (1).

 Unscrew the cap and inspect to

see whether there is oil on the

lower edge of the filling opening.

 If the oil level is too low, top it up

with sufficient lubricating oil up

until the lower edge of the filling

opening using a funnel with a

flexible spout.

 Replace the fill cap on the wheel

transmission and screw it tight.

Lubricate according to the

lubrication plan

 Use a grease gun at the grease

nipples. High-quality lubricating

oil should be applied regularly to

other moving parts without

grease nipples.

Draining condensation from

the diesel filter

Note

The diesel filter is located to the

right, on the engine. The fuel filter

contains a tap for draining off

condensation (water) which is

residue from the diesel and has

collected on the filter base.

 Stop the engine and place

a suitable container below the

filter draining tap.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

MTD CubCadet serie 6000 Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von MTD CubCadet serie 6000

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info