Bedienungsanleitung MTD Zero Turn Serie Frontcut (Seite 11 von 18) (Englisch)

495078

Zoom out

Zoom in

Vorherige Seite

1/18

Nächste Seite

English Operating Instructions

PTO-switch (I)

Fig. 8

The PTO switch switches the cutter

deck/accessories on and off via an

electromechanical clutch.

ON = pull the switch.

OFF = press the switch.

Note

When the safety lock system has

automatically switched OFF the

appliance (e. g. when reversing with

activated cutters), first switch ON and

then OFF the PTO switch to release

the lock on the clutch.

Combination indicator (J)

Fig. 9

According to the model,

the combination indicator can

consist of the following elements.

Oil pressure (1):

If the indicator light lights up when

the engine is running, switch the

engine off immediately and check

the oil level. Where necessary,

visit a garage.

Brake (2):

Indicator lamp lights up if the brake

pedal is not depressed or the

parking brake is not locked when

the engine starts.

Cutter deck (PTO) (3):

The indicator lamp lights up when

the cutters are not switched OFF

at engine start (PTO).

Battery charge indicator (4):

If the indicator light lights up when

the engine is running, this means

that the battery is not sufficiently

charged. Where necessary,

visit a garage.

Operating hour counter/

Battery voltage (5):

This function shows the operating

hours as full hours and

of an hour

in the display.

Note

– When the ignition is switched on,

the battery voltage indicator is

indicated for a short period and

then the operating hours are

indicated.

– The operating hours are always

counted except for when the

ignition key is in the “Stop”

position or when it is removed.

– Each time 50 operating hours

have elapsed (according to the

model), the oil change indicator

“CHG/OIL” appears in the display

for five minutes. This message

appears after the next two hours

of operation. See the engine

manual for oil change intervals.

Can holder (K)

Fig. 1

Gear release lock lever (L)

Fig. 10

To push the unit when the engine

is switched off, pull up both levers,

then pull out and press down.

To drive, put back/push in both

levers.

Engine hood holder (M)

Fig. 1

To open the engine hood,

remove the retaining rubber.

Seat adjustment lever (N)

Fig. 11

The driver’s seat can be set with

the seat adjustment lever.

Lever for setting the cutting

height (O)

Fig. 12

Largest cutting height, cutters top =

lever to “H”.

Smallest cutting height, cutters

bottom = lever to “L”.

To adjust the lever, press the button

(a) and adjust the lever (b). Release

button and engage lever in the

required position.

Note

When exchanging the cutting

height, the cutting mechanism

wheels/rollers have to be

correspondingly reset. See section

“Setting the cutting mechanism”.

Ratchet plate for setting the

cutting height (P)

Fig. 1

Cutting height can be adjusted from

approx. 3.8 cm to approx. 11 cm.

Each notch corresponds to a height

adjustment of approx. 0.9 cm.

Chokelevel (Q) (depending

on model)

Fig. 13

To start a cold engine, pull the choke

(Figure 13a), or move the accelerator

lever to (Figure 13b).

Arm rests (R)

Fig. 1

Hydraulic oil expansion tank

(S)

Fig. 1

Is used as an expansion vessel for

the hydraulic fluid during operation.

Maintenance and inspection only by

a specialist company during annual

maintenance.

Fuel tank (T)

Fig. 1

Tank contents display (U)

Fig. 23

shows the fill-level of the fuel tank

on the see-through window.

Light (optional)

The headlights are lit as long as the

engine is running or the ignition is

switched on.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

MTD Zero Turn Serie Frontcut Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von MTD Zero Turn Serie Frontcut

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info