Bedienungsanleitung Multiplex PROFIcar4000 (Seite 8 von 16) (Englisch)

30242

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

PROFI mc 4000PROFI mc 4000

Version 2.0

Slow for mixer input

;SERVO 5:ELEV.+

INPUT 2:ELEVATOR Ä

,02.0sec' #01.0sec_

The maximum delay time is 25 seconds, and the

value can be set separately for both directions.. The

time statement always refers to full servo travel, -

100% to +100% (=200%). For example, if you have

set 20% elevator trim compensation for the SPOILER

mixer input, then the elevator moves to the new set-

ting in 2.5 seconds.

Example:

Compensating for an unwanted pitching moment due

to incorrect motor downthrust (model climbs when the

throttle is opened).

The mixer ELEVATOR+ has been set up with

THROTTLE as one of the inputs. This provides a

means of correcting the model’s unwanted tendency

to climb when the throttle is opened. Nothing new

there.

What is new is that the „slow“ mixer can now be

added. Naturally the model’s unwanted pitching mo-

ment builds up gradually, i.e. it follows the model’s

rate of acceleration. Even if you use a switch to open

the throttle (electric motor), it can take several sec-

onds before the pitching moment takes full effect.

The same applies when you close the throttle (or

switch off the electric motor), but this time in reverse.

In the next section you will see how to adjust the

times for „running up“ (,0.00 sec') and „running

down“ (#0.00 sec_) for the input.

To correct the power moment we wish to add and

subtract the THROTTLE input slowly relative to the

ELEVATOR+ mixer. At the same time the application

of up- or down-elevator is slowed due to the set

SLOW delay, and this allows you to adjust the re-

sponse speed of the THROTTLE input to

ELEVATOR+ exactly to match the model’s behaviour.

This is how it’s done:

Button Effect

b b

Hot keys to reach

the „Servo adjustments“ menu

On to the „SLOW“ menu

Slow for mixer input

;SERVO 5:ELEV.+

INPUT :THROTTLE Ä

,02.0sec' #03.5sec_

-100% to +100% +100% to -100%

Open „Servo“ select field

and select the servo

(x) Open the „Input“ adjust field and select

the input to be adjusted

The input line only appears if more

than one input is present!

g or w Select adjust field for the desired di-

rection,

set time using q/n or the Digi-

adjustor, range 0,1 sec to 25,0 sec

6.2 Transmitter control options vary-

ing with flight mode

This is how it used to work:

If you moved to „Menu 1: Adjustments“ and select the

CONTROLS point, the top line of the screen always

displayed the name of the current flight mode.

This is how it works now:

The name of the flight mode is only displayed if the

selected option can be set differently in the various

flight modes.

If the setting applies to all flight modes (SLOW, trim

travel, trim method, AUTO-TRIM) then the top line is

left blank. This gives you a visual reminder that the

settings apply to all modes.

6.3 Control switch status

displayed on the screen

This is how it used to work:

When adjusting the switching threshold you could

previously only see the % value on the screen. You

could only check where the switching point lay with

reference to the transmitter control travel if the control

switch was also assigned to a function.

This is how it works now:

In „Menu 2: Assigning SWITCHES“ an asterisk („*“)

appears next to the control’s code letter if the associ-

ated control is in the „ON“ range.

Assign switches

CONTROL SW.: C1 Ä

;FROM CONTROL: A *

,1-POINT: MAX + 0%_

The same applies if you define the switch as a 2-

position switch.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Multiplex PROFIcar4000 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info