Bedienungsanleitung Multiplex Razor (Seite 17 von 56) (Deutsch, Englisch, Französisch, Italienisch, Spanisch)

561614

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

Operating Instructions

MULTIcont BL-15 brushless controller

MULTIPLEX Modellsport GmbH & Co.KG • Westliche Gewerbestraße 1 • D-75015 Bretten • www.multiplex-rc.de Page 2/4

Anleitung MULTIcont BL-15 # 82 5959 (12-04-26/BRAN) • Errors and omissions excepted. •



MULTIPLEX

Connecting the three-core lead (UNI connector system) to

the receiver

Connect the three-core receiver lead (attached to the speed

controller) to the receiver input socket used for motor speed

control:

- With MULTIPLEX RC systems: channel 4 = throttle / motor

- With HiTEC RC systems: channel 3 = throttle / motor

Pin assignment

Negative pin (−)

brown

Positive pin (+) red

Signal ( ) orange

Do not connect a separate receiver battery to the receiver,

as the controller supplies current to the receiver and servos

via the BEC circuit. Always keep to the maximum servo

count limit in BEC mode (



 2.). Disable the BEC system if

necessary (



 7.).

5. USING THE UNIT FOR THE FIRST TIME

By default, MULTIcont BL-15 speed controllers are set up for

use with LiPo batteries; the brake is ON.

1. Using the MULTIcont BL-15 controller for the first

time

1.1 Programmable RC

system

set servo travel for

throttle / motor to

100% in both

directions

1.2 Move transmitter

throttle stick (and trim,

if present) to the motor

OFF position

1.3 Transmitter ON

1.4 Connect a fully-

charged flight battery

⇒ Rising sequence of tones

⇒ In LiPo mode the number of

beeps indicates the detection

of a LiPo battery with X cells

(in NiXX mode the following

signals are emitted immediately)

⇒ Two rising tone sequences

⇒ Controller is ready for use

! Note:

Programmable parameters

If you wish to change one of the programmable parameters,

please refer to the Programming section ( 6.).

Start-up protection

MULTIcont BL-15 speed controllers are only armed when the

throttle stick is moved to the motor OFF position, and when the

audible “ready” indication has been emitted.

Always carry out a range check

Every time you wish to fly, carry out a range check with the RC

system switched on. Check in particular that radio range is not

diminished at full-throttle and half-throttle, and that no

interference occurs. Watch the servos in the model: if they jitter

or carry out random movements, this indicates an interference

problem which must be solved.

6. PROGRAMMING

Programming the MULTIcont BL-15 speed controller could

hardly be simpler; it is carried out using the transmitter throttle

stick or - for even greater convenience - the MULTIPLEX

MULTImate # 8 2094.

Beeps indicate the status of programming when using the

transmitter stick, and also confirm any changes. The procedure

runs through all variable parameters step by step. You select the

desired programming option by moving the throttle stick either to

the full-throttle or motor OFF position. Returning the stick to

centre takes you on to the next programmable parameter.

Activate programming mode

0.1

Flight battery disconnected

Stick to full-throttle position

Transmitter ON

0.2

Connect fully-charged flight

battery

⇒ Rising tone sequence

⇒ In LiPo mode:

Indicates detected LiPo

cell count

⇒ in NiXX mode the

following signal is emitted

immediately

⇒ Rising tone sequence

0.3

Stick to centre position

⇒ Rising tone sequence

0.4

Stick to full-throttle position

⇒ Rising tone sequence

0.5

Stick to centre position

⇒ Rising tone sequence

sounds four times: the

controller is now in

programming mode

Select battery mode

(single beep, continuously repeated)

1.1

Automatic low-voltage cut-

off for LiPo batteries*

→ stick to full-throttle

position

OR:

For NiXX batteries

→ stick to motor OFF

position

⇒ Long tone

(confirmation signal)

1.2

Stick to centre position

Select brake mode

(double beep, continuously repeated)

2.1

For brake ON*

→ stick to full-throttle

position

OR:

For brake OFF

→ stick to motor OFF

position

⇒ Confirmation signal

emitted

2.2

Stick to centre position

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Multiplex Razor Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info