Bedienungsanleitung Multiplex ROYALevo12 (Seite 32 von 57) (Englisch)

30266

Zoom out

Zoom in

Vorherige Seite

1/57

Nächste Seite

Instructions

Page 87

12.12. Template: HELIccpm

suitable for:

Main rotor control systems with electronic mixers

CCPM (Cyclic-Collective-Pitch-Mixing)

with 3 or 4 servos, 90° to 150°

Typical models:

ECO 8, Logo, Fury, Three Dee NT, Uni-Expert

12.12.1. Assigned transmitter controls and switches

Assignment used: HELI

A : Sum timer ´ controlled by THR.LIMITER (F)

Dual-Rates Direct Main Throttle

A/E/R Throttle phase CUT

OFF OFF OFF

Phase 1-3 Gyro Thr. limiter (Direct Thr.)

1: HOVER Centre Minimum

12.12.2. Assigned servos / receiver outputs

The default setting in the HELIccpm model template is a

120° swashplate with the pitch-axis servo at the rear.

12.12.3. Fine-tuning

a. Check stick functions (roll, pitch-axis, yaw)

Select different mode if necessary (è 13.3.1.)

L, Assignment, Mode

b. Check direction of servo rotation for all functions

If necessary change servo direction (REVERSE)

K, Calibrate, select servo, Parameter REV/CLR

c. Gyro features

è 15.3.

13. Main menu „Setup“ L

This main menu is primarily concerned with settings

which apply to the transmitter generally.

ü This symbol indicates global settings which influ-

ence the behaviour of the transmitter generally.

I Some settings apply only to the selected model.

These are marked with the model memory symbol.

13.1. Sub-menu „Transmitter“

13.1.1. Parameter „Trim graphics“

ü global effect

The current state of the trims can be displayed on

screen in any of 6 different ways (trim graphics 0 to 5).

We suggest that you try out the variants and set the one

which you find easiest to see at a glance.

13.1.2. Parameter „Sounds“

ü global effect

With this parameter you determine which events in the

transmitter trigger an audible signal.

Setting Audible signal

Battery

when battery voltage

falls below alarm threshold

Batt+Time

as 1. + timer alarm

B+Ttim+Tr

as 2. + trim adjustments

Init off

all, except during power on

All

always

13.1.3. Parameter „Battery alarm“

ü global effect

Range 6,50 to 7,5 V (0,01V increments)

Default setting 6,9 V

The battery alarm is intended to alert you to a failing

battery, i.e. the charge is only sufficient for a limited

residual operating time.

! The lower you set the threshold, the shorter the

remaining residual operating time.

The residual operating time varies very widely accord-

ing to the set threshold and the state of the battery. For

this reason it is important that you should carry out a

test to establish how much residual time is available in

your particular case.

This is done by switching on the transmitter with the

aerial fully extended, and the RF module with crystal (or

synthesizer) installed. You don’t need to move the

sticks. Set the alarm threshold to the desired value, and

leave status display 1 or 2 on the screen to show the

battery voltage.

Now time the period from the first audible alarm warn-

ing until the minimum operating voltage (6.5 V) is

reached).

! The transmitter switches itself off automatically

at around 6.3 V!

13.1.

13.2.

13.3.

13.4.

13.5.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Multiplex ROYALevo12 Seite 32

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Multiplex ROYALevo12

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info