Bedienungsanleitung Multiplex ROYALevo12 (Seite 53 von 57) (Englisch)

30266

Zoom out

Zoom in

Vorherige Seite

1/57

Nächste Seite

ROYAL evo

Page 108

18. Main menu „Memory“ II

The ROYALevo has 20 or 36 model memories, depend-

ing on the version you have purchased. The memory

spots are numbered continuously. You can also enter a

name with up to 16 characters for each model memory.

The model data is stored in an area of non-volatile me-

mory, and cannot be lost even if you disconnect the

transmitter battery from the transmitter.

In addition to memory management (switching, copy-

ing, erasing) you can also use this menu to create new

models (è 18.6.) and manage the flight phases you set

up (è 18.4.).

18.1. Sub-menu „Select model“

(change memory)

When you move to this sub-menu, the screen displays a

list showing all the model memories. The top of a typi-

cal list might look like this:

The active model memory is marked with the letter x.

An empty model memory is marked with --------.

Vacant memories can be managed, but not activated.

To change models simply select the memory you wish

to use, then press the 3-D digi-adjustor or the ENTER

button.

18.2. Sub-menu „Copy“

In this menu you can copy all the setup values relating

to the transmitter controls, mixers, servos, timers, model

name and trims.

The copy process is carried out in four stages:

1. Select the model which is to be copied.

This can be any model.

2. Confirm your selection with the 3-D digi-adjustor

or ENTER button. The letter after the model name

changes from x to c (copy).

3. Seek the destination

The model name and the “c” are carried along with

you during the search.

4. Confirm the destination with the 3-D digi-adjustor

or ENTER button.

• If the destination memory is empty, the copy proc-

ess is carried out immediately.

• If the destination memory already contains data,

you will see the security query:

“Overwrite existing model?”

• At this point you can interrupt the copy process by

pressing the ENTER button or the 3-D digi-adjustor.

• If you wish to overwrite the existing model data,

press the REV/CLR button.

When the copy process is finished, the software calls up

the previously active model again.

18.3. Sub-menu „Erase“

When you have selected the memory you wish to erase,

press the 3-D digi-adjustor or the ENTER button. The

screen displays the security query “Erase selected

model?”.

• If you do not want to erase the data:

Press ENTER or the 3-D digi-adjustor.

• If you do want to erase the data:

Confirm by pressing the REV/CLR button.

You cannot erase model data if you have selected the

active model memory, i.e. the one marked with the

letter “x”.

18.4. Sub-menu „Flight phases“

I affects active model memory

4 phases are possible

Phases are switched “smoothly”

(over approx. 1 sec)

Phase name can be selected from 13 pre-sets

Phases can be released and blocked

(alarm sound if you select a blocked phase)

Phases can be copied

You can adjust the characteristics of the transmitter

control to suit the requirements of the model for each

flight phase separately, e.g. reduced control travels for

SPEED FLYING, lowered flaps for LANDING, greater col-

lective pitch travel for AUTO-ROTATION. Where settings

are present which can be altered separately for each

flight phase, the code number of the flight phase ap-

pears in the transmitter control menus (è 14.2.).

Basic requirement: if you wish to work with flight

phases, you must first assign at least one phase select

switch (main phase or phases 1-3) in the menu L, AS-

SIGNMENT, SWITCHES. If no switch is assigned, the

transmitter remains permanently in Phase 1.

A typical Flight Phase menu might look like this:

This display tells us the following:

1. Flight phases 2 and 3 are blocked

(name crossed through)

2. Flight phase 1 (main phase) is active

(x after the name)

3. Main phase switch is switch J on the right-hand side

4. No switch is currently assigned to phase 4

(--- after phase 4)

18.4.1. Selecting flight phase names

The following names are available:

NORMAL, START1, START2, THERMAL1, THERMAL2,

SPEED1, SPEED2, CRUISE, LANDING, AUTOROT, HOVER,

3D, ACRO

The phase names are only intended as a reminder for

the operator. The significant factor in the characteristics

of the flight phase is always the number of that phase.

You can select a suitable name after activating the

name input field.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Multiplex ROYALevo12 Seite 53

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Multiplex ROYALevo12

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info