Bedienungsanleitung Multiplex ROYALevo12 (Seite 54 von 57) (Englisch)

30266

Zoom out

Zoom in

Vorherige Seite

1/57

Nächste Seite

Instructions

Page 109

18.4.2. Block / release flight phase

Use the REV/CLR button to release or block the flight

phases. First select the flight phase, then activate the

name, and finally switch between “free” and “blocked”

using the REV/CLR button. Selecting a different name

using the 3-D digi-adjustor also releases a blocked flight

phase. The active flight phase (x) cannot be blocked.

NOTE:

If you accidentally select a blocked flight phase with the

phase select switch, you will hear a continuous warning

tone. The settings of the last used phase remain active,

the corresponding phase number appears in the display

and the phase name appears striked out.

18.4.3. Copying the active flight phase

The active flight phase is marked by an “x” after the

name. You can copy the values for this phase into any of

the three other phases. This is the procedure:

1. Select the active phase (x)

2. Press the 3-D digi-adjustor (or ENTER) twice:

the “x” is activated

3. Select the destination phase for the copy: a “c” ap-

pears in the cursor.

4. Confirm with the 3-D digi-adjustor or ENTER

18.5. Sub-menu „Properties“

I affects active model memory

Displays model template used to create this model

This menu displays certain characteristics of the active

model. These characteristics can also be changed, with

the exception of the used template.

Example:

In this example Mode indicates that the left stick con-

trols rudder and elevator. You can change this setting if

you wish.

Assignment indicates which of the available assign-

ment lists for transmitter controls and switches is in use

for this model. You can change this setting if you wish.

Template indicates the model template you invoked

when you created this model. You cannot change this

setting.

he name of the model can be entered at this point, with

a maximum of 16 characters. If you create a new model,

the name of the template you used is automatically

entered here.

18.6. Sub-menu „New model“

When you open this sub-menu the following display

appears:

The transmitter tells you which memory number will be

used: it is always the first vacant memory. You cannot

change the memory number.

The template determines which basic settings are ac-

cepted into the memory (è 12.4.). You can change this

setting if you wish.

Servo conf. (Servo configuration) defines the assign-

ment of the servos and the signal format. The following

combinations are possible:

Servo conf..

Servo

assignment

Signal format

MPX-MPX

MPX MPX

MPX-UNI

MPX UNI

Futaba

Futaba UNI

JR UNI

Mode defines the assignment of the sticks. In our ex-

ample the left-hand stick controls rudder and elevator.

You can change this setting if you wish.

Assignment defines which of the possible assignment

lists for transmitter controls and switches is to be used

with this model. You can change this setting if you wish.

Select OK to conclude the process, and the new model

is created.

Note:

If there are no vacant memories available, the screen

displays the number -1 and the note “No memory free!”

In this case press ENTER and then “EXIT” the menu.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Multiplex ROYALevo12 Seite 54

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Multiplex ROYALevo12

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info