Bedienungsanleitung Multiplex ROYALevo7 (Seite 48 von 77) (Englisch)

30268

Zoom out

Zoom in

Vorherige Seite

1/77

Nächste Seite

ROYAL evo 7 - Instructions

Page 47

ENGLIS

16.2.2. Free assignment with model helicopters

If you have set up a model helicopter based on one of

the model templates HELImech or HELIccpm, various

transmitter controls can be selected for the free or vari-

able channels. You can find out which channels are free

or variable by consulting the descriptions of the heli-

copter model templates (Î 20. onward):

Available

controls

Note

Pitch-ax

Pitch-axis signal only no mixing

Yaw

Yaw signal only no mixing

Throttle

Throttle signal, plus mixed throttle curve,

throttle limiter, direct throttle, EMERGENCY

throttle CUT

Spoiler

Spoiler signal only no mixing

RPM

Control signal for speed controller

L. gear

Retract signal no mixing

Aero-tow

Aero-tow signal mixing

Brake

Brake signal mixing

Gyro

Gyro signal, including all mixed signals

from the

Gyro mixer

Mixture

Mixture signal only no mixing

AUX1

AUX2

AUX1/2 signal only no mixing

Coll. P.

Coll. pitch signal only no mixing

16.2.3. Special features when assigning

The transmission mode PPM 6 or PPM 7 is set automati-

cally:

Last servo on channel 6  PPM 6

Last servo on channel 7  PPM 7

Problems may occur with PPM 6 and certain older types

of speed controller, in which case it may help to assign

any function to channel 7. This forces PPM 7 operation;

you do not need to connect a servo to the output.

16.3. Sub-menu: Monitor

The Servo Monitor is a substitute for a receiving system

and servos, enabling you to check the function and op-

eration of servos, speed controllers and - especially -

gyro systems (for which an external effect is not easy to

detect), and seek and eliminate faults.

Call up the menu, then press the ENTER button or a 3D

digi-adjustor; the Servo Monitor then appears.

Two display variants are available:

x graphic, with bar-form display of output signals

(Fig. 1), and

x numerical, with display of % values (Fig. 2).

You can switch between the two displays using the UP /

DOWN buttons ( / ) or one of the two 3D digi-

adjustors.

Press the ENTER button or one of the 3D digi-adjustors

to close the Servo Monitor.

16.4. Sub-menu: Test run

Automatic servo run, designed for test and demonstra-

tion purposes or as an “electronic aid” for range-

checking.

As soon as you select a transmitter control, the transmit-

ter generates a constant control signal with variable

transit time, i.e. from one end-point of the control to the

other. All servos which are operated by this transmitter

control, either directly or via a mixer, start running.

You can interrupt the test run by either of two methods:

x Press the REV/CLR button  “ Control

“ appears

x Select no transmitter control (“ - - - - - - - “)

The transit time can be set to any value in the range 0.1

– 4.0 seconds.

17.Main Menu Timer A

The ROYALevo7 features a stopwatch with alarm func-

tion which can be used for various timing tasks. The

stopwatch counts up to 4½ hours with a resolution of

one second.

Line 1:

Time

This is the time which has elapsed since the timer

started. If you select this field, you can erase the time

using the REV/CLR button.

The stopwatch can also be reset by pressing the

REV/CLR button when you are in one of the status dis-

plays 1 - 3.

Line 2:

Alarm

This is where you set the alarm time. For example, if the

motor run of an electric-powered model is four minutes,

you should set

0:04:00 at this point. The timer adds

together the motor run time based on the throttle set-

ting, and emits a warning sound once the set alarm time

has elapsed.

The method of entering the alarm time differs from the

usual procedure: here the value is entered digit by digit:

press the ENTER button or one of the 3D digi-adjustors.

The cursor jumps to the hours, which can then be set

using the UP / DOWN buttons or one of the 3D digi-

adjustors. Every time you press ENTER again, the cursor

moves one place to the right etc.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Multiplex ROYALevo7 Seite 48

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Multiplex ROYALevo7

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info