Bedienungsanleitung Multiplex ROYALevo7 (Seite 50 von 77) (Englisch)

30268

Zoom out

Zoom in

Vorherige Seite

1/77

Nächste Seite

ROYAL evo 7 - Instructions

Page 49

ENGLIS

18. Main Menu Memory I

The ROYALevo7 has 15 model memories, numbered se-

quentially. You can assign a name up to 16 characters

long to each model memory.

The model data is stored in non-volatile memory, and

therefore cannot be lost even if you disconnect the

transmitter battery from the transmitter.

In addition to memory management (switching, copy-

ing, erasing), you can also set up new models (Î 18.6.)

and manage flight phases (Î18.4.) in this menu.

18.1. Sub-menu: Select model

(switch memories)

When you move to the Select model menu, you will

see a list of all 15 model memories:

The active model memory is marked

Empty model memories have no model name:

“

--------“.

It is possible to select an empty memory, but not acti-

vate it.

To switch models, select the appropriate memory using

the UP / DOWN buttons ( / ) or one of the two 3D

digi-adjustors, then press the ENTER button or one of

the 3D digi-adjustors. The screen then switches to the

last used status display. The transmitter is immediately

ready for use, and the model can be flown.

18.2. Sub-menu: Copy

Making a copy of one model memory can be a useful

time-saver if, for example, you wish to set up a new

model which is similar to one you already own, or if you

want to make experimental changes to the settings of a

model without losing the existing settings. The copy

process copies all the settings for the transmitter con-

trols, mixers, servos, timers, model name and trims.

There are four steps to copying a model memory:

1. Select the model

Select the model which is to be copied using the UP

/ DOWN buttons ( / ), or one of the two 3D digi-

adjustors.

2. Confirm your selection

Press the ENTER button or one of the 3D digi-

adjustors.

 The letter “c” (= copy) now appears after the

model name (Fig. 1).

3. Define the destination

Select a target memory for the copy using the UP /

DOWN buttons ( / ) or one of the two 3D digi-

adjustors. The model name of the model to be cop-

ied and the “c” go with you on the search (Fig. 2).

4. Confirm the destination

Press the ENTER button or one of the 3D digi-

adjustors.

Fig. 1 Fig. 2

x If the destination memory is empty, the copy is cre-

ated immediately.

x If the destination memory is already occupied, the

security query appears: “Overwrite existing model?”.

x At this point you can interrupt the copy process by

pressing the ENTER button or one of the 3D digi-

adjustors.

x If you wish to overwrite the existing model, press

the REV/CLR button.

After the copy process the previously active model is

called up again.

18.3. Sub-menu: Erase

If you wish to erase a model memory, first select the

memory, then press the ENTER button or one of the 3D

digi-adjustors. A security query now appears:

x If you wish to erase it,

press the REV/CLR button to confirm your action;

x If you do not wish to erase it,

press the ENTER button or a 3D digi-adjustor.

Erasing is not possible if you have selected the mem-

ory marked

x, as this memory is currently active.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Multiplex ROYALevo7 Seite 50

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Multiplex ROYALevo7

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info