Bedienungsanleitung Multiplex ROYALevo7 (Seite 51 von 77) (Englisch)

30268

Zoom out

Zoom in

Vorherige Seite

1/77

Nächste Seite

ROYAL evo 7

Page 50

18.4. Sub-menu: Flight phases

Flight phases are groups of settings (data) which can be

called up for a particular model by operating a switch.

The settings can be optimised for different flight tasks.

For each flight phase you can adjust the transmitter

control settings individually to suit the requirements of

the model (e.g. reduced travels for SPEED, extended

flaps for LANDING, different collective pitch and throttle

curves for model helicopters, …). All the settings which

can be modified for the various flight phases are as-

signed the code numbers 1 … 3 or 4 associated with the

flight phase (Î 14.). The ROYALevo7 also features flight

phase specific digital trims (Î 12.), i.e. the trims can be

set separately for each flight phase, and the settings are

stored permanently. This simply means that the model

is always perfectly trimmed in each flight phase.

For fixed-wing model aircraft we have provided three

flight phases. Flight phases 1 … 3 are selected using

switch J: “F-PH 1-3”.

For model helicopters an additional fourth flight phase

is provided for auto-rotation. This is selected using

switch I “A-ROT”, and always has highest priority. This

means: the auto-rotation flight phase

AUTOROT is al-

ways activated when switch I “A-ROT” is operated, re-

gardless of the flight phase 1 …3 currently selected us-

ing switch J “F-PH 1-3”.

The transition between flight phases is “soft” (it takes

about one second), in order to avoid sudden servo

movements when the change-over is made. The excep-

tion to this rule is the auto-rotation flight phase with

model helicopters. If you operate switch I “A-ROT”, the

transition to the

AUTOROT flight phase occurs immedi-

ately.

The Flight phase menu for a fixed-wing model may look

like Fig. 1; for a helicopter like Fig. 2:

Fig. 1 Fig. 2

Fig. 1 contains the following information:

x The first column shows the number of the flight

phase, followed by the name of the flight phase

x Flight phases 1 and 3 are blocked

(names crossed out)

x Flight phase 2

NORMAL is currently active

(

x after the name)

x The flight phase switch is

J> on the right-hand side.

The same applies to the four helicopter flight phases

shown in Fig. 2.

18.4.1. Selecting names for flight phases

The following flight phase names are available:

NORMAL, START1, START2, THERMAL1, THERMAL2,

SPEED1, SPEED2, CRUISE, LANDING, HOVER, 3D, ACRO

The name serves only as information to the user. The

number of the flight phase is crucial to its properties, i.e.

flight phases of the same name do not necessarily share

the same settings or characteristics.

This is the procedure for changing a flight phase

name:

Use the UP / DOWN buttons (▲ / ▼ ) or one of the two

3D digi-adjustors to select a flight phase, and confirm

your action by pressing the ENTER button or one of the

3D digi-adjustors  the cursor jumps to the name input

field.

You can now select a suitable name using the UP /

DOWN buttons (▲ / ▼ ) or one of the two 3D digi-

adjustors.

Press the ENTER button or a 3D digi-adjustor to con-

clude the procedure. Note: this requires a double press

if you have changed the name of the currently active

flight phase.

Exception

The name for flight phase 4 for helicopters is

AUTOROT,

and this cannot be changed.

18.4.2. Blocking / releasing flight phases

You can release or block any flight phase using the

REV/CLR button. By blocking a flight phase you can

eliminate the danger of launching a model after acci-

dentally selecting a flight phase which does not contain

the correct settings.

If you select a blocked flight phase using one of the

flight phase switches J (“F-PH 1-3”) or I (“A-ROT”), you

will hear a continuous warning sound. The last used

flight phase remains active, and its number is shown in

status display 2. The name of the blocked flight phase

which you have selected is shown crossed out.

This is the procedure for blocking / releasing flight

phases:

Select a flight phase, then press the ENTER button or

one of the 3D digi-adjustors to confirm your action 

the cursor jumps to the flight phase name. You can now

switch between “free” and “blocked

” using the REV/CLR

button.

Selecting another name using the 3D digi-adjustor also

releases a blocked flight phase.

Note:

The currently active flight phase (marked with

x) cannot

be blocked.

18.4.3. Copying flight phases

We recommend the following procedure if you wish to

make a start using different flight phases:

Begin with just one flight phase, leaving the other flight

phases blocked. Your model should now be test-flown

and all settings carefully optimised. The flight phase can

now be copied. When you switch to the new flight

phase(s) you can be confident that the model will be-

have in the usual manner. All you have to do now is

make the desired modifications to the copies.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Multiplex ROYALevo7 Seite 51

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Multiplex ROYALevo7

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info