Bedienungsanleitung NAD M 2 (Seite 6 von 14) (Englisch)

493487

Zoom out

Zoom in

Vorherige Seite

1/14

Nächste Seite

IDENTIFICATION OF CONTROLS

FRONT PANEL

1 STANDBY LED: This indicator will light up amber when M2 is in

standby state. When M2 is at ON state, this indicator will illuminate blue.

2 STANDBY BUTTON: Press this button to switch ON the M2. The

Standby LED indicator will turn from amber to blue and illuminate the

VFD. Pressing the STANDBY button again turns the unit back to standby

mode.

IMPORTANT NOTICE

The rear panel POWER switch must be set to ON position for the

STANDBY button to activate. After pressing the STANDBY button, there

will be a delay before the M2 will be completely enabled. Please wait

until the initial “NAD M2” display in the VFD is extinguished before you

select any of the source input or features of your M2.

3 VACUUM FLUORESCENT DISPLAY (VFD): Display visual information

about the selected source input, menu options, volume level and other

related information and settings.

4 VOLUME: Use this control to adjust M2’s overall amplication or volume

level. Turn clockwise to increase the volume setting; counter clockwise

to lower it. The M2 features a “velocity sensing” volume control; rapid

movement changes the volume in large steps, slow movement increments

the volume in 0.5dB steps. The VOLUME knob is also used to select options

or adjust settings when MENU button is activated.

5 COAX 1: Select the source connected to the COAX 1 rear panel

terminal as the active input.

6 COAX 2: Select the source connected to the COAX 2 rear panel

terminal as the active input.

7 OPTICAL 1: Select the source connected to the OPTICAL 1 rear panel

terminal as the active input.

8 OPTICAL 2: Select source connected to the OPTICAL 2 rear panel

terminal as the active input.

9 AES/EBU: Select the source connected to the AES/EBU IN rear panel

connector as the active input.

10 BALANCED: Select the source connected to the BALANCED L and

BALANCED R rear panel connectors as the active input.

11 SINGLE-ENDED: Select the source connected to the SINGLE-ENDED L

and SINGLE-ENDED R rear panel terminals as the active input.

12 LOOP (DIGITAL PROCESSOR LOOP): Allow the insertion of external

digital lters into the signal path. This is the digital equivalent of the

analog “Tape Monitor Loop”. An example on how to take advantage of

this feature is illustrated below.

a Connect a digital input to the rear panel’s OPTICAL 1 TosLink optical

terminal.

b Connect the rear panel’s OPTICAL LOOP OUT to a compatible

OPTICAL IN of a Mac or any processor where the signal can be

subjected to a wide library of crossover lters, equalization or room

correction programs (Check if your Mac or processor has these

feature capabilities).

c Send out the processed signal from your Mac or processor’s

corresponding Optical Out port into M2’s OPTICAL LOOP IN thereby

completing the signal loop path.

d Press front panel’s “loop” button to select your OPTICAL 1’s

“processed” input signal. When “loop” feature is engaged, “LOOP” will

be continuously displayed at the lower left corner of the VFD after a

brief display of sample rate setting of the source.

IMPORTANT NOTICE

With “loop” button enabled, there will be no audio output if any

connection from the above “loop” setup example is “broken” (i.e., no

connection to OPTICAL OUT, not looped to “OPTICAL LOOP IN”, etc). Press

“loop” button again to deactivate or turn o the “loop” feature (“LOOP”

is extinguished in the VFD) thus returning to normal audio listening of a

selected source input.

NOTE

This digital processor loop feature can be applied to all analog and

digital audio input signal sources (Optical 1-2, Coax 1-2, AES/EBU,

BALANCED and SINGLE-ENDED).

765 8

432

9 10 11 12 13

ENGLISH FRANÇAIS ESPAÑOL ITALIANO DEUTSCH NEDERLANDS SVENSKA РУССКИЙ

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

NAD M 2 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von NAD M 2

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info