Bedienungsanleitung NAD M17 AV (Seite 14 von 38) (Englisch)

562261

Zoom out

Zoom in

Vorherige Seite

1/38

Nächste Seite

TONE CONTROLS

The M17 has three Tone Control levels – Treble, Bass and Center Dialog. Bass

and Treble controls only aect the low bass and high treble leaving the

critical midrange frequencies free of coloration. The Center Dialog (“Dialog”

in the VFD) control boosts the “presence” of the midrange region improving

intelligibility of speech.

These controls allow one to tweak on-the-y, the frequency response

of the source during playback. The control setting could be adjusted by

navigating through the Tone Controls’ OSD menu via a combination of

[ENTER] and [W/E/R/T] keys. The same can be managed directly by

pressing the front panel’s “Tone” display and then press and slide “h“ to

adjust treble, bass or dialog level.

Maximum and minimum values for all three Tone Control levels are ±10 dB.

“Tone Defeat” gives one the choice of varying or completely bypassing the

tone control section of the M17. If “O” (“Tone Active” in the VFD) is selected,

the Tone Control circuits are active.

Select “On” (“Tone Defeat” in the VFD) to bypass the Tone Controls eectively

defeating the eect of the tone control circuits.

NOTE

Tone Controls options can be directly selected or changed using

HTRM2’s TONE button with DEVICE SELECTOR set to AMP mode. Toggle

TONE button to select “Treble”, “Bass” or “Dialog” and then use the

[R/T] to adjust their respective levels. Press TONE again to save the

settings and at the same time move on to the next parameter or exit the

parameter setting altogether.

ZONE CONTROLS

Depending on the settings made at the separate “Zone Setup” menu

under the “Setup Menu”’ section discussion, the applicable Zone can be

congured and managed via this “Zone Controls” window.

Select “On” to activate the applicable Zone. When activated, the Source

input for the particular Zone can be allocated by selecting through the

following inputs – All enabled Sources and Local.

Select “Local” as your selected Zone’s Source input if you wish to enjoy the

same source as the main Zone and allow simultaneous listening, but with

full separate volume levels.

If a Zone is set to “O”, it is deactivated or powered o.

“Volume” refers to the adjustable secondary Zone 2 Volume level that can

be increased or decreased using the [R/T] buttons of the HTRM 2.

Zone 2 is always available to be congured at “Zone Controls” menu. For

Zone 3 and Zone 4 to become available at the “Zone Controls” window,

their corresponding “Mode” in the “Zone Setup” menu under the “Setup

Menu” section should be set to “Zone (Audio Only)”.

NOTES

• The ZR 7 remote control will only control Zone 2 applications. Zone 3

and Zone 4 could be congured and managed at the appropriate Zone

OSD menu using the corresponding keys on the HTRM 2 remote control.

• “Zone 4” is audio only and not associated with any video input sources.

OPERATION

USING THE M17  MAIN MENU

ENGLISH FRANÇAIS ESPAÑOL ITALIANO DEUTSCH NEDERLANDS SVENSKA РУССКИЙ

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

NAD M17 AV Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von NAD M17 AV

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info