Bedienungsanleitung NAD M17 AV (Seite 17 von 38) (Englisch)

562261

Zoom out

Zoom in

Vorherige Seite

1/38

Nächste Seite

DIGITAL AUDIO

To take advantage of the M17’s high performance surround and digital

audio circuitry, it is advisable that its sets of Digital Audio input are selected.

There are three types of Digital Audio input for the M17. These are HDMI,

Optical and Coaxial digital input. A fourth option is “O” whereby no

incoming digital audio signal is selected by the particular Source.

The desired digital audio input for a particular Source can be selected by

scrolling to “Digital Audio”, press [E] and then [R/T] to step through the

desired digital input source. After nalizing the desired type of Digital Audio

input, press [E] and then [R/T] again to select the specic Digital Audio

input.

The following are the sets of assignable Digital Audio input:

HDMI $ HDMI 1- 6

Optical $ Optical 1-4

Coaxial $ Coaxial 1-4

NOTE

An incoming digital signal present at the assigned digital input will

always take precedence over the assigned analog audio input, even if

both are present. To maintain the analog audio input for the particular

Source, select “O” at the “Digital Audio” setting of the same “Source”

menu.

VIDEO

There are three types of video input a particular Source could be assigned.

These are HDMI, Component and Video input. Another option is “O”. Select

“O” if it is intended not to assign any video input to a particular Source.

Navigate through the Video input selections by pressing [E] and then

[R/T] to step through the selections. The following are the sets of

assignable Video input.

HDMI $ HDMI 1-6

Component Video $ Component 1 - 2

Video $ Video 1 - 3

IMPORTANT NOTE ABOUT THE VIDEO PERFORMANCE OF M17

The M17 utilizes an NAD-engineered eld-programmable gate array

(FPGA) that is capable of enabling the conversion of analog video to

digital video. This allows a single cable connection to your TV for all

sources while maintaining the source’s native resolution. Interlaced

video is converted to progressive scan over HDMI allowing complete

compatibility with latest HD TVs.

The M17 also supports HDMI 1.4a features that include compatibility with a

broad range of 3D and HD digital video sources and displays.

A/V PRESET

A particular Source can be assigned a stored Preset. The parameters set up

in the selected Preset number will be adopted into the particular Source it

is assigned (Please refer to the separate section on “A/V Presets” for further

understanding of Preset settings).

Scrolling to “A/V Preset” and by pressing [E] and then [R/T], a Source

could be assigned a Preset number ranging from Preset 1 to 5.

If it is desired not to assign the particular Source a Preset setting, select

“None”.

TRIGGER OUT

Trigger Out feature for a particular Source is dependent upon the

congurations done in a separate menu on Trigger Setup (See “Trigger

Setup” below). If “Source Setup” is assigned to all three Trigger output

(Trigger Out 1-3) in the separate “Trigger Setup” menu window, a particular

Source can have the following Trigger Out combinations

Trigger Out: 1 $ 2 $ 1 + 2 $ 3 $ 1 + 3 $ 2 + 3 $ 1+2+ 3

These combinations are dependent upon the assignment of “Source Setup”

for Trigger 1 Out, Trigger 2 Out or Trigger 3 Out at the “Trigger Setup” menu.

Another option is “None” whereby the particular Source is not assigned any

Trigger Out.

For “Trigger Out” to become enabled and assignable at “Source Setup

(Normal View)” menu, make sure to carry out or note the following

beforehand

• In the separate “Trigger Setup” menu, assign Trigger 1 Out, Trigger 2 Out

or Trigger 3 Out to “Source Setup.”

• “Trigger Out” will not appear as an option at the Source Setup (Normal

View) menu if at the separate “Trigger Setup” menu, Trigger 1 Out,

Trigger 2 Out or Trigger 3 Out are all assigned to “Main, Zone 2, Zone

3, Zone 4, Zone 2+3+4, Main + Zone 2, Main + Zone 3, Main + Zone 4

or Main + Zone 234”; with not even one “Trigger Out” port allocated to

“Source Setup.”

SOURCE SETUP (TABLE VIEW)

The Source Setup (Table View) reects the settings made in the Source

Setup (Normal View) menu. All the Source settings are summarized and

displayed in tabulated form in the Source Setup (Table View).

Navigating through the Source Setup (Table View) via a combination

of [W/E] and then [R/T] buttons, one will have the benet of directly

changing the settings for “Audio”, “Video”, “Preset”, “Trigger” and “Name”

without going back to the Source Setup (Normal View) menu.

Highlight a particular Source number and then, toggle [ENTER] button to

enable or disable said Source number.

OPERATION

USING THE M17  SETUP MENU

ENGLISHFRANÇAISESPAÑOLITALIANODEUTSCHNEDERLANDSSVENSKAРУССКИЙ

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

NAD M17 AV Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von NAD M17 AV

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info