Bedienungsanleitung NAD M32 DirectDigital DAC Amplifier (Seite 6 von 24) (Englisch)

667811

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

1 POWER INDICATOR

• This indicator will be amber when the M32 is in standby mode.

• When the M32 is powered up from standby mode, this indicator

will change from amber to bright white color.

2 o(STANDBY)

• Touch the o (Standby) button on top of the unit to switch the

M32 ON from standby mode. The Power indicator will change from

amber to bright/white color.

• Press and hold o (Standby) button until M32 switches back to

standby mode.

• One press or touch of the o (Standby) button will not switch the

M32 to standby mode. This is intended to avoid unintentionally

setting the M32 to standby mode if one happens to just touch or

press the o (Standby) button at operating mode.

• The Power indicator will change to amber color at standby mode.

• The o (Standby) button cannot activate the M32 if the rear panel

POWER switch is o.

• Refer also to +12V TRIGGER - REAR PANEL.

IMPORTANT NOTES

For the o (Standby) button to activate, the following must occur:

a The supplied power cord from the M32 must be plugged in to a

power source.

b The rear panel POWER switch must be set to ON.

3 HEADPHONE

• A /” stereo jack socket is supplied for headphone listening and will

work with conventional headphones of any impedance.

• The volume, tone and balance controls are operative for

headphone listening. Use a suitable adapter to connect

headphones with other types of sockets, such as 3.5mm “personal

stereo” jack plugs.

4 REMOTE SENSOR

• Point the HTRM 2 remote control at the remote sensor and press

the appropriate buttons.

• Do not expose the remote sensor of the M32 to a strong light

source such as direct sunlight or illumination. If you do so, you may

not be able to operate the M32 with the remote control.

Distance: About 23 ft. (7 m.) from the front of the remote sensor.

Angle: About 30 degrees in each direction of the front of the

remote sensor.

5 DISPLAY (TOUCH PANEL DISPLAY)

• Displays visual and menu information according to the settings

selected.

• The following display options are accessible via the touch panel

display - Main, Media, Mode, EQ and Setup.

• Touch the screen to select any of the display options, to see their

corresponding menu options, or settings.

6 VOLUME

• The VOLUME control adjusts the overall loudness of the signal sent

to the loudspeakers. The Volume control is characterized by perfect

signal tracking and channel balance. It provides a highly linear and

low noise operation.

• Turn clockwise to increase the volume level and counter clockwise

to lower it.

• The default volume level is -20dB.

IDENTIFICATION OF CONTROLS

FRONT PANEL

5 63 4

ENGLISH FRANÇAIS ESPAÑOL ITALIANO DEUTSCH NEDERLANDS SVENSKA РУССКИЙ

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

NAD M32 DirectDigital DAC Amplifier Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von NAD M32 DirectDigital DAC Amplifier

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info