Bedienungsanleitung NAD M32 DirectDigital DAC Amplifier (Seite 8 von 24) (Englisch)

667811

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

7 POWER

• The POWER switch supplies the master AC mains power for the

M32.

• When the POWER switch is set to ON position, the M32 goes to standby

mode as shown by the amber status condition of the front panel Power

indicator. Press the front panel Standby button or HTRM 2’s remote

control’s [ON] button to switch ON the M32 from standby mode.

• If you do not intend to use the M32 for long periods of time (such

as when on vacation), switch o the POWER switch.

• With POWER switched o, neither the front panel Standby button

nor HTRM 2 remote control’s [ON] button can activate the M32.

8 DIGITAL AES/EBU

• Connect SACD/CD Players or processors to this XLR connector for

digital audio streaming.

• High-end sources with higher sampling rates (176kHz and 192kHz)

should be connected to the AES/EBU IN connector.

9 COMPUTER

• Use a Type A to Type B cable connector (not supplied), to interface

computer audio to this asynchronous Type B USB input to directly

stream 24/96 PCM content from your PC or MAC.

• The Type A-style connector is a at, rectangular interface.

• The Type B-style interface is square in shape and has beveled

corners on the top ends of the connector.

• Refer to LISTENING TO COMPUTER in the OTHER FEATURES section

on the OPERATION page.

10 SERVICE

Use for servicing purposes only. Not for consumer use.

11 INPUT

PHONO: Input for a Moving Magnet (MM) phono cartridge. Connect

the twin RCA lead from your turntable to this input if you are using a

Moving Magnet cartridge.

LINE1, LINE 2: Input for line level sources such as CD player, tuner or

any compatible devices. Use a twin RCA-to-RCA lead to connect the

source device’s left and right “Audio Output” to this input.

12 OUTPUT (PRE-OUT/SUBW)

• These output terminals have dual function. They are used either as

PRE-OUT or SUBWOOFER terminals.

• The M32 and associated external devices must be turned OFF always

before connecting or disconnecting anything to the OUTPUT sockets.

IMPORTANT

Set the “Sub Output” option under “Speaker Setup” settings to “ON” for

the OUTPUT terminals to function as Subwoofer out. On the other hand,

the OUTPUT terminals will function as PRE-OUT if the “Sub Output”

option is set to “OFF”.

PRE-OUT

• The PRE OUT/SUBW sockets make it possible for the M32 to be used

as a full range preamplier to an external power amplier.

• Use a dual RCA cable to connect PRE-OUT/SUBW to the

corresponding analog audio input of compatible devices such as

ampliers, receivers or other applicable devices.

• PRE-OUT/SUBW will be aected by the M32’s volume control

settings. Turn the VOLUME control to adjust the output level of the

PRE OUT/SUBW sockets.

SUBWOOFER

• Use a dual RCA cable to connect PRE OUT/SUBW to the low level

input of a powered subwoofer.

• Low frequency information up to 200Hz is sent to the connected

subwoofer via PRE OUT/SUBW.

13 AC MAINS INPUT

• The M32 comes supplied with two separate mains power cords.

Select the mains power cord appropriate for your region.

• Before connecting the plug to the mains power source, ensure that

it is rmly connected to the M32’s AC Mains input socket.

• Always disconnect the mains power plug from the mains power

source before disconnecting the cable from the M32’s AC Mains

input socket.

14 FUSE HOLDER

• Only qualied NAD service technicians can have access to this fuse

holder. Opening this fuse holder may cause damage thus voiding

the warranty of your M32.

15 GROUND TERMINAL

• Ensure that the M32 is plugged-in to a grounded AC wall outlet.

• If necessary, use this ground terminal to connect to ground a

phono or turntable source for PHONO input.

• If a separate earth ground is necessary, use this terminal to ground

your M32. The M32 can be connected to ground by connecting a

ground lead wire or similar to this terminal. After insertion, tighten

the terminal to secure the lead.

NOTES

• The above illustration shows the M32 being connected to ground via

a metal water pipe. There maybe other grounding conductor points

in your home. Consult with a licensed electrician to locate or install

a grounding conductor in your home. NAD is not responsible for

any malfunction, damage or costs associated with the installation,

connection, or grounding of your M32.

• The grounding wire is not supplied with your M32.

IDENTIFICATION OF CONTROLS

REAR PANEL

ENGLISH FRANÇAIS ESPAÑOL ITALIANO DEUTSCH NEDERLANDS SVENSKA РУССКИЙ

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

NAD M32 DirectDigital DAC Amplifier Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von NAD M32 DirectDigital DAC Amplifier

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info