Bedienungsanleitung NAD M32 DirectDigital DAC Amplifier (Seite 9 von 24) (Englisch)

667811

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

MDC CLASSIC UPGRADE SLOTS

The delivery format of digital content is constantly changing in pure digital

systems like the M32. Each of these formats typically requires specialized

hardware and software, often with licensed IP and content copy protection.

To address continuous technological evolution, NAD has placed all digital

interface circuitry of the M32 on easily upgradable modules, called Modular

Design Construction (MDC). The M32 includes one MDC module – the DD

SPDIF which has digital coaxial, optical and AES/EBU input terminals.

There are three optional MDC modules – the DD HDM-1, the DD AP 1 and

the MDC BluOS modules. Remove covers to install the optional Modular

Design Construction (MDC) modules.

Consult with your NAD dealer on how to procure the DD HDM-1, the DD

AP 1 and MDC BluOS modules and their installations to the M32.

DD HDM-1 (DIRECT DIGITAL HDMI)

The DD HDM-1 oers three HDMI input terminals and one HDMI output

with video pass through. With DD HDM-1 installed, the M32 can be the

heart of a “Video 2.0” system using the mandatory 2 channel linear PCM

soundtrack from Blu-ray or DVD to make a compelling high denition

theater presentation. DD HDM-1 is fully 3D video compatible without

surround sound decoding or video processing.

A HDMI OUT: Connect the HDMI Monitor OUT to a

HDTV or projector with HDMI input.

B HDMI 1 -3: Connect to the HDMI OUT

connectors of source components such as DVD

player, BD player or HDTV satellite/cable box.

WARNING!

Before connecting and disconnecting any

HDMI cables, both the M32 and the source must be powered OFF and

unplugged from the AC outlet. Failure to do so may cause permanent

damage to equipment connected via HDMI sockets.

DD AP 1 (DIRECT DIGITAL ANALOG-PHONO)

DD AP 1 uses high quality Analog-to-

Digital conversion to make analog sources

compatible with M32’s pure digital circuitry.

The PHONO circuit has impedance settings for

Moving Magnet (MM) and Moving Coil (MC)

with gain automatically set.

The DD AP 1 consists of the following line

level input terminals – PHONO, SINGLE-ENDED

(ANALOG) and BALANCED.

A PHONO: Input for either a MM or MC

phono cartridge. Connect the twin RCA

lead from your turntable to this input.

B SE IN (SINGLE-ENDED): Use a twin RCA-to-RCA lead to connect these

sockets to the left and right analog output of a CD player, preamplier

or processor.

C PHONO GROUND CONNECTOR: Turntables normally include a single

wire earth lead. Use the M32 phono ground connector to connect this

lead. Unscrew the terminal and insert the ground wire into the hole.

Tighten the terminal to secure the lead.

D BALANCED: Connect XLR audio sources to these connectors. Ensure

that proper pin congurations are followed – Pin 1: Ground, Pin 2:

Positive (signal live) and Pin 3: Negative (signal return).

MDC BluOS

BluOS is a music management software developed by NAD’s sister brand,

Bluesound. Integrating MDC BluOS will add BluOS network and internet

music streaming with advanced music management to your M32.

Refer to “MDC DD BluOS Mounting Instructions” and” Configuring DD

BluOS” for instructions on how to install and integrate the MDC BluOS with

the M32.

IMPORTANT NOTE

BluOS audio cannot be streamed through digital output terminals.

BluOS PLAYBACK CONTROLS

Using the HTRM-2 remote control, the following control buttons are

applicable for BluOS playback. Set DEVICE SELECTOR to MP for BluOS

playback control.

4 : Resume playback from pause mode.

; : Pause current playback.

7 : Skip back to the beginning of current song.

8 : Skip forward to the next song.

REPEAT : Repeat song, playlist, all or repeat o.

RANDOM : Play songs/playlist in random order.

IDENTIFICATION OF CONTROLS

REAR PANEL

ENGLISHFRANÇAISESPAÑOLITALIANODEUTSCHNEDERLANDSSVENSKAРУССКИЙ

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

NAD M32 DirectDigital DAC Amplifier Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von NAD M32 DirectDigital DAC Amplifier

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info