Bedienungsanleitung NAD M32 DirectDigital DAC Amplifier (Seite 7 von 24) (Englisch)

667811

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

1 COAX 1-2, OPT 1-2

• Connect to the corresponding optical or coaxial digital output of

sources such as CD or BD/DVD players, digital cable box, digital

tuners and other applicable components.

2 COAXIAL OUT, OPTICAL OUT,

• Connect the optical or coaxial DIGITAL OUT to a corresponding

digital audio input of compatible devices such as receivers,

computer soundcards or other digital processors.

NOTE

Only digital sources can be streamed through COAXIAL/OPTICAL

DIGITAL OUT.

3 +12V TRIGGER

+12V TRIGGER OUT

The +12V TRIGGER OUT is used for controlling external equipment

equipped with a +12V trigger input.

• Connect this +12V TRIGGER OUT to the other equipment’s

corresponding +12V DC input jack using a mono cable with 3.5mm

male plug.

• This output will be 12V when the M32 is ON and 0V when it is either

OFF or in standby mode.

+12V TRIGGER IN

With this input triggered by a 12V DC supply, the M32 can be switched

ON remotely from Standby Mode by compatible devices such as

ampliers, preampliers, receivers, etc. If the 12V DC supply is cut o,

the M32 will return to standby mode.

• Connect this +12V Trigger input to the remote device’s

corresponding +12V DC output jack using a mono cable with

3.5mm male plug. The controlling device must be equipped with a

+12V trigger output to use this feature.

4 IR IN

• This input is connected to the output of an IR (infrared) repeater

(Xantech or similar) or the IR output of another component to allow

control of the M32 from a remote location.

5 RS 232

NAD is a certied partner of AMX and Crestron and fully supports

these external devices. Check out the NAD website for information

about AMX and Crestron compatibility with NAD. See your NAD audio

specialist for more information.

• Connect this interface using RS-232 serial cable (not supplied) to

any Windows compatible PC to allow remote control of the M32 via

compatible external controllers.

• Refer to the NAD website for information about RS232 Protocol

documents and PC interface program.

6 SPEAKERS

• The M32 has two sets of SPEAKER connections which are identical

in function (parallel connection). They allow for bi-wiring.

• Connect M32’s Right speaker terminals marked “R +” and “R-” to

the corresponding “+” and “-“ terminals of your designated right

speaker. Repeat the same for M32’s Left speaker terminals and

corresponding left speaker.

• Double check the speaker connections before powering up the

M32.

BI-WIRING

Most high quality loudspeakers oer the option of Bi-wiring. This

separates the High Frequency (HF) crossover from the Low Frequency

(LF) crossover. This oers enhanced performance by preventing LF

returned currents from aecting the HF performance. To bi-wire,

remove the “links” at the loudspeaker that connect the LF and HF

sections (these are provided for convenience when a single wire

connection is used).

NOTES

• Use 16 gauge (American Wire Gauge or AWG) or lower stranded wire.

Connections to the M32 can be made with banana-type plugs.

• Bare wire or pins can also be used by loosening the terminal’s plastic

nut, making a clean, neat connection and re-tightening. To minimize

the danger of a short circuit, ensure that only 1/2-inch of exposed wire

or pin is used to connect and no loose strands of speaker wire.

IDENTIFICATION OF CONTROLS

REAR PANEL

SERVICE

COMPUTER

COAX1

COAX2

OPT1

OPT2

AES/EUB IN

M o d u l a r

D e s i g n

C o n s t r u c t i o n

M o d u l a r

D e s i g n

C o n s t r u c t i o n

M o d u l a r

D e s i g n

C o n s t r u c t i o n

LINE 1

PHONO

PRE-OUT/SUBW

LINE 2

INPUT OUTPUT

1 2 3 4 5 6 7

1098 11 12 13 14 15

ATTENTION!

Please ensure that the M32 is powered o or unplugged from the main power source before making any connections. It is also advisable to power down or

unplug all associated components while making or breaking any signal or AC power connections.

ENGLISHFRANÇAISESPAÑOLITALIANODEUTSCHNEDERLANDSSVENSKAРУССКИЙ

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

NAD M32 DirectDigital DAC Amplifier Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von NAD M32 DirectDigital DAC Amplifier

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info