Bedienungsanleitung NAD t 585 (Seite 13 von 26) (Englisch)

137301

Zoom out

Zoom in

Vorherige Seite

1/26

Nächste Seite

BRIGHTNESS/CONTRAST/SATURATION/SHARPNESS/GAMMA

Picture Setting adjustment is available for the following options.

Brightness: Adjust overall brightness of the image.

Contrast: Adjust bright areas (white level) in the image.

Saturation: Adjust the dullness or richness of image color. A color

with absolutely no saturation is going to be gray. A color that is 100%

saturated is in its most intense form.

Sharpness: Picture sharpness could be easily lost during the

recording/playback process. Adjust sharpness to improve the ne

details of the picture

Gamma: Adjust intensity of the picture non-linearly. Select when

an image’s dark portions appears obscure or bright portions become

brighter than necessary.

NOTES

• The level of adjustment for Brightness, Contrast, Saturation and

Sharpness (all defaulted to “0”) range from -4 to +4 while Gamma is

from 0.761 up to 1.315.

• Refer also to the item on PICTURE SETTING ADJUSTMENT at the VIDEO

SETTING section of the REFERENCE page.

VIDEO OUTPUT

Turn ON/OFF either HDMI audio/video OUT or VGA OUT. HDMI OUT and

VGA OUTPUT can only be turned ON one at a time – if HDMI is set to ON,

VGA is automatically set to OFF and vice versa.

SCART EUROPE MODEL ONLY

SCART carries both composite video and RGB signals. Select the video

output signal that will be routed over SCART OUT.

CVBS: Select to output composite video signals.

RGB: Split the signal into the three fundamental colors Red, Green and

Blue (RGB) resulting to greater picture resolution and elimination of

artifacts associated with traditional composite video signals.

AUDIO SETUP MENU

DIGITAL AUDIO OUTPUT

Each DVD disc has a variety of audio output options. Set the player’s Digital

Audio Output according to the type of audio system you use.

DOLBY DIGITAL/PCM: Select DOLBY DIGITAL/PCM if an active digital

output is supplied to a Dolby Digital decoder (or an amplier or other

equipment with Dolby Digital decoder). In this mode, the T 585 will

automatically switch between Dolby Digital and PCM depending on

the program encoded on the disc, with Dolby Digital given priority. DTS

is not possible with this setting.

Stream/PCM: Select Stream/PCM if an active digital output is supplied

to an amplier or other equipment with DTS decoder, Dolby Digital

decoder and MPEG decoder. If the disc is neither of stream or PCM

format, there will be no audio output at this option.

PCM: Select when connected to a two-channel digital stereo amplier.

DVDs encoded in Dolby Digital or MPEG will be automatically

downmixed to two-channel PCM audio. DTS cannot be downmixed to

two-channel PCM.

O: Select to turn o digital audio output. With this option, you will

have purely analog audio output.

NOTES

• If an active digital audio output signal is supplied to a receiver or other

equipment without a corresponding digital decoding capability, a very

loud noise may be produced which could permanently damage the

speakers.

• The DTS DVD disc sound is played back only when the DVD player is

connected to a receiver with a DTS decoder.

5.1 SPEAKER SETUP

This option allows you to congure the 5.1 CHANNEL AUDIO OUT of the

T 585. Digital audio output will not be aected by the settings done in this

section. Use [ ] keys to select a menu item and [ ] keys to adjust

the settings of the selected item.

SPEAKER SELECTION

Select a speaker that you want to adjust - Front L, Center, Front R, Rear R,

Rear L or Subwoofer.

SIZE

Small: Select if you have connected to a system with speakers that lacks

signicant deep bass response - about 150Hz below.

Large: Select if you have connected to a system with full frequency

speakers capable of deep bass response.

None: Select when you do not have a certain speaker connected.

Front L/R speaker’s size can only be set to “Large” or “Small”. If Front L/R

speaker’s size is set to “Small”, Rear and Centre speaker’s size can only be set

to “Small” or “None”.

Subwoofer’s size can be set only to “Large” or “None”.

VOLUME

Adjust the output level of the selected speaker from -10dB up to a

maximum of 0dB.

DISTANCE

Setting the Distance lets the speakers know how far the sound has to travel

to reach your set listening point. This allows the sound from each speaker to

reach the listener at the same time.

Distance can be adjusted within 1ft (0.30m) up to 20ft (6m).

DISTANCE setting is not applicable for Subwoofer.

OPERATION

USING THE T 585  SETUP MENU

ENGLISHFRANÇAISESPAÑOLITALIANODEUTSCHNEDERLANDSSVENSKAРУССКИЙ

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

NAD t 585 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von NAD t 585

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info