Bedienungsanleitung NAD T 747 (Seite 10 von 42) (Englisch)

493497

Zoom out

Zoom in

Vorherige Seite

1/42

Nächste Seite

18 ZONE 2 FIX, ZONE 2 VAR: Connect both ZONE 2 FIX and ZONE 2 VAR

to the corresponding audio input of an external integrated amplier,

preamplier or receiver.

FIX: When FIX is the selected ZONE 2 audio output port, the ZONE 2

volume level can only be varied by using the VOLUME control of the

external amplier or receiver it is connected to. Neither the front panel

VOLUME nor ZR 5’s [VOL ] can vary Zone 2 audio output.

VAR: If VAR is the selected ZONE 2 audio output port, the Zone 2

volume level can be adjusted depending upon the setting of the

“Volume” item (either Fixed or Variable setting) in the Zone 2 Controls

OSD menu.

For a better understanding of Zone 2 features, refer to the item about

ZONE 2 CONTROLS under the USING THE T 747 - MAIN MENU segment

of the OPERATION section.

19 AUDIO 5 IN/OUT, AUDIO 6: Input for additional line level input signals

such as CD player, MP player or other line-level signal source. Connect

AUDIO 5 OUT to the analog audio input of a recording component such

as a CD recorder or to an outboard audio/video processor. Connect the

AUDIO 5 IN jacks to the component’s corresponding output.

AUDIO 6 IN is ideal for the connection of the analog output of line-level

audio sources like a CD player or Stereo tuner.

20 SPEAKERS: Connect the respective speaker’s FRONT L, FRONT R,

CENTER, SURR R, SURR L, SURR-BL channels to their corresponding

loudspeakers. Make sure the “+” (red) terminal and “-” (black) terminal are

connected to the corresponding “+” and “-” terminals of the loudspeaker.

Use extra care to ensure that no stray wires or strands cross between

posts or terminals at either end.

The T 747 is designed to produce optimum sound quality when connected

to speakers with impedances within its operating range. Please make sure

that all the speakers are rated 8 ohms minimum per speaker.

NOTE

Use stranded wire of at least 16 gauge (AWG). Connections to the T 747

can be made with banana plugs (120 V version model only) or by using

bare wire or pins. Use the transverse hole through the post for bare-wire

or pin connections. By loosening the terminal’s plastic nut, make a

clean, neat connection and re-tighten carefully. To minimize the danger

of short-circuit, ensure that only 1/2-inch of exposed wire or pin is

employed when connecting.

21 SWITCHED AC OUTLET: This convenience outlet can supply switched

power to another component or accessory. It is powered ON and OFF

by the front panel POWER button or by the AVR 3’s ON and OFF keys.

The total draw of all devices connected to this outlet must not exceed

100 watts.

22 AC MAINS INPUT: The T 747 comes supplied with a separate AC Mains

cable. Before connecting the cable to a live wall socket, ensure that it

is rmly connected to the T 747’s AC Mains input socket rst. Connect

only to the prescribed AC Outlet, i.e., 120V 60 Hz (for 120V version

models of T 747 only) or 230V 50 Hz (for 230V version models of T 747

only). Always disconnect the AC Mains cable plug from the live wall

socket rst, before disconnecting the cable from the T 747’s Mains input

socket.

IDENTIFICATION OF CONTROLS

REAR PANEL

ENGLISH FRANÇAIS ESPAÑOL ITALIANO DEUTSCH NEDERLANDS SVENSKA РУССКИЙ

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

NAD T 747 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von NAD T 747

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info