Bedienungsanleitung NAD T 747 (Seite 30 von 42) (Englisch)

493497

Zoom out

Zoom in

Vorherige Seite

1/42

Nächste Seite

FRONT PANEL DISPLAY SETUP

The Vacuum Fluorescent Display (VFD) and On-Screen Display (OSD) can be

shown in various ways by navigating through the parameters at the “Front

Panel Display Setup” menu.

DISPLAY

Select “On” to display all applicable data or characters at the VFD. Nothing

will be shown at VFD if “Temp” is selected. However at “Temp” setting,

whenever any of the front panel controls or their corresponding keys in the

remote control is activated, the appropriate VFD characters will be shown

temporarily and then fade away.

DIMMER

If it is desired to reduce the brightness of the VFD, set Dimmer to “Dim”.

Otherwise, select “Bright” to return to normal VFD brightness.

LINE 1, LINE 2

The VFD shows two main lines of data or characters. Line 2 is the line of

data or characters located at the lower bottom of the VFD while directly

above it is Line 1. For both lines, one can select which display could be

shown by choosing through the following

Main Source: Shows the active Source.

Volume: Current Volume level is shown.

Listening Mode: Selected Listening Mode is shown.

Audio Src Format: Shows the audio format detected at the active Source.

Zone 2 Source: The assigned Source for Zone 2 is shown.

O: Select “O” if it is desired not to show any data at the applicable Line.

TEMP LINE

Choose between Line 1 and Line 2 as the desired line where VFD will be

temporarily shown if “Temp” is selected at “Display” option as described

above.

NOTE

The congurations set forth at “Front Panel Display Setup” are carried

over whenever it is enabled during A/V Preset setting. Refer also to the

item about A/V PRESETS under the USING THE T 747 – SETUP MENU

segment of the OPERATION section.

VIDEO SETUP

This menu allows you to set the display resolution of the T 747 along with

the compatible video format setting and picture setup.

VIDEO FORMAT

There are 2 options under Video format – Resolution to Display and

Frame Rate.

Resolution to Display: The T 747 has the excellent ability to

upconvert standard denition video contents to high denition video

signal. Depending upon your TV/Monitor’s resolution capabilities, select

the applicable resolution settings - Auto, 480i/576i, 480p/576p, 720p,

1080i and 1080p. When “Auto” is selected, the T 747 automatically selects

the highest resolution compatible with the connected TV/Monitor.

Note that if the display is connected to Composite or S-Video Monitor

OUT, the video output resolution must be set to 480i or 576i to view

content.

When you change the resolution setting, you will be prompted to Save

or Cancel the resolution change as per the message shown in OSD.

IMPORTANT NOTE

Some TV/Monitors may not be able to handle simultaneous High

Denition (HD) video input contents of 720/1080 as fed through their

HDMI and Component Video inputs. If T 747’s “Resolution to Display”

setting is set to “Auto” and a source input is fed to any of the T 747’s

HDMI IN rear panel ports and HDMI MONITOR OUT connected to a video

display, component video output will only be available at 480i/576i or

480p/576p resolution. At this condition, changing the resolution setting

from “Auto” to a high denition setting like 720p, 1080i or 1080p may

result to a distorted display at Component Video Monitor OUT.

In order to attain a high denition setting at Component Video Monitor

OUT, there should be NO connection made through any of the HDMI

inputs and HDMI Monitor OUT. It is suggested to use standard denition

resolution for simultaneous output and use EITHER Component or HDMI

for high denition output.

OPERATION

USING THE T 747  SETUP MENU

ENGLISH FRANÇAIS ESPAÑOL ITALIANO DEUTSCH NEDERLANDS SVENSKA РУССКИЙ

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

NAD T 747 Seite 30

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von NAD T 747

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info