Bedienungsanleitung NAD T 747 (Seite 32 von 42) (Englisch)

493497

Zoom out

Zoom in

Vorherige Seite

1/42

Nächste Seite

The T 747’s internal AM/FM tuner oers very high quality sound from radio

broadcasts. The reception and sound quality will always be dependent to a

degree however on the type of antenna(s) used as well as proximity to the

broadcast origin, geography and weather conditions.

ABOUT ANTENNAS

Connect the supplied lead-type FM antenna to the FM antenna input. Extend

the lead. Experiment freely with your antenna placement and orientation until

you get the clearest sound and lowest background noise. Fix the antenna in

the desired position by using thumb tacks, push pins or any suitable means. In

areas of poor FM reception, an exterior FM antenna can improve performance

dramatically. If radio listening is important to you, consider consulting an

antenna installation professional to optimize your system.

The AM loop antenna supplied with the T 747 (or a suitable replacement)

is required for AM reception. Open the clip terminal lever; insert the wire

making sure to match the color-coded (white and black) ends of the

wire to that of the terminal and close the lever ensuring that the lever

locks the wire in place. Testing dierent positions for the antenna may

improve reception; vertical orientation will usually produce the best results.

Antenna proximity to large metal objects (appliances, radiators) may impair

reception, as will attempts to lengthen the wire to the loop.

The supplied AM “loop” antenna will usually provide adequate reception.

However, an exterior AM antenna can be used to improve reception.

Consult an antenna professional for more information.

IMPORTANT NOTICE

Unless otherwise specically stated, navigating or accessing AM/FM

functions can be undertaken by using either the AVR 3 remote control

or the front panel buttons. If the control button or icon button being

referred to is available on the AVR 3 remote control and front panel,

then the reference to said button is applicable to both the AVR 3 remote

control and front panel.

NOTE

When using the AVR 3 remote control to carry out AM/FM commands,

ensure that the DEVICE SELECTOR is set to “TUN”.

ASSEMBLING THE LOOP ANTENNA

1 Rotate the outer frame of the antenna.

2 Insert the bottom edge of the outer frame into the groove on the stand.

3 Extend the antenna cord.

SELECTING A TUNER BAND

Press the [AM/FM/DB] button on the AVR 3 while at AMP or TUNER device

selector page. Each subsequent press of either button will toggle you

through AM, FM and XM (or DAB) band. Stop (release button) at your

desired tuner band.

TUNING AM/FM STATIONS

Upon selecting AM or FM band, use [TUNE ] on the AVR 3 to

perform slow manual search; press and hold to automatically search.

The front panel or AVR 3’s [ ] buttons can also be used to tune for

stations.

1 Press [ ] momentarily to step up or down between AM or FM

frequencies.

2 Press and hold [ ] for more than 2 seconds to search up or down

- the T 747’s tuner will stop at the next suciently strong signal it

encounters.

3 Pressing the [ ] during the search process will stop the search.

DIRECT TUNING

If you know your desired station’s frequency allocation, you can tune

directly to the station.

1 Toggle [ENTER] button to switch between “Preset” and “Tune” mode (see

the lower line of the VFD). Select “Tune” mode.

2 Using the numeric keys of the remote control, key-in the frequency

allocation of the station. For example, to enter 104.50MHz, press “1”, “0”,

“4”, “5” and “0” or press “”1”, “0”, “4” and “5”.

SETTING RADIO PRESETS AM/FM

The T 747 can store up to 30 FM and 30 AM stations for immediate recall.

1 To store a radio preset, rst tune the desired frequency (see above), then

press AVR 3’s [MEMORY] key.

2 The VFD will show the next available Preset number (If there are no more

vacant Preset number, you can overwrite an existing Preset number

by pressing the [ ] buttons to select the Preset number you want

to overwrite). Press the [MEMORY] button again to store the desired

frequency on the Preset number shown (or use the [ ] buttons to

select another available Preset number and then, press [MEMORY] button

again). Your desired frequency is now stored in the assigned preset.

Press [ ] to step up or down between presets. Press and hold [ ]

to “scroll” continuously up or down. The AVR 3 remote’s [PRESET ]

keys work similarly.

OPERATION

LISTENING TO AM/FM RADIO

ENGLISH FRANÇAIS ESPAÑOL ITALIANO DEUTSCH NEDERLANDS SVENSKA РУССКИЙ

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

NAD T 747 Seite 32

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von NAD T 747

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info