Bedienungsanleitung NAD T 758 (Seite 9 von 42) (Englisch)

745046

Zoom out

Zoom in

Vorherige Seite

1/42

Nächste Seite

5 IR IN/IR OUT 1-2

These mini-jacks accept and output remote-controlled codes in

electrical format, using industry-standard protocols, for use with “IR-

repeater” and multi-room systems and related technologies.

• All NAD products with IR IN/IR OUT features are fully compatible

with the T 758. For non-NAD models, please check with your other

product’s service specialists as to their compatibility to the T 758’s IR

features.

IR IN

This input is connected to the output of an IR (infrared) repeater

(Xantech or similar) or the IR output of another component to allow

control of the T 758 from a remote location.

IR OUT 1, IR OUT 2

When connected to the IR IN of an ancillary equipment, direct the

ancillary equipment’s own remote control to the T 758’s infrared

receiver to command or control the linked unit.

IR IN and IR OUT 1, IR OUT 2

Connect the T 758’s IR IN to the IR OUT of an ancillary equipment.

Connect also the T 758’s IR OUT 1 to another equipment with IR IN

feature. With this setup, the T 758 acts as an “IR-repeater” allowing the

equipment connected to the T 758’s IR IN control or command of the

other equipment linked to the T 758’s IR OUT 1. A combination of IR IN

and IR OUT 2 also perform the same function.

6 +12V TRIGGER OUT

The +12V TRIGGER OUT is used for controlling external equipment that

is equipped with a +12V trigger input.

• Connect this +12V TRIGGER OUT to the other equipment’s

corresponding +12V DC input jack using a mono cable with 3.5mm

male plug.

• This output will be 12V when the T 758 is ON and 0V when it is shut

down or at standby mode.

7 MP DOCK

The T 758 is equipped with a data port in the rear panel where an

optional NAD IPD (NAD IPD Dock for iPod) 1, NAD IPD 2 and later

variants can be plugged in.

• Connect the MP DOCK (DATA PORT) jack of the T 758 to the

corresponding DATA PORT socket of the optional NAD IPD model.

• AUDIO 3 and S-VIDEO 1 are the assigned default ports for the audio/

video output of the separately sold NAD IPD (NAD IPD Dock for

iPod) 1, NAD IPD 2 and later variants.

• Refer also to the LISTENING TO YOUR iPod PLAYER segment of the

OPERATION section.

NOTE

The NAD IPD Dock for iPod is not supplied with your T 758.

8 DAB MODULE INPUT (230V version model only)

The T 758 is compatible only with the NAD DAB Adaptor module

models DB 1 or DB 2.

• Plug-in the other end of the Mini-Din connector from the NAD DAB

Adaptor module output port into this socket.

• With DAB, you can receive CD-like quality programs without any

annoying interference and signal distortion.

• Refer also to the LISTENING TO DAB RADIO segment of the

OPERATION section.

9 RS 232

NAD is a certied partner of AMX and Crestron and fully supports

these external devices. Check out the NAD website for information

about AMX and Crestron compatibility with NAD. See your NAD audio

specialist for more information.

• Connect this interface using RS-232 serial cable (not supplied) to

any Windows compatible PC to allow remote control of the T 758

via compatible external controllers.

• Refer to the NAD website for information about RS232 Protocol

documents and PC interface program.

10 MONITOR

Connect to the video input of a monitor/television using quality

composite video cable.

VIDEO 1-2/S-VIDEO

Connect these composite video and S-video input ports to the

corresponding video output ports of source components such as

DVD players, cable/satellite boxes or other compatible line level video

sources.

11 AC MAINS INPUT

• The T 758 comes supplied with a separate detachable mains power

cord. Before connecting the plug to the mains power source,

ensure that it is rmly connected to the T 758’s AC Mains input

socket rst.

• Always disconnect the mains power plug from the mains power

source rst, before disconnecting the cable from the T 758’s AC

Mains input socket.

12 SWITCHED AC OUTLET

This convenience outlet can supply switched power to another

component or accessory.

• The total draw of all devices connected to this outlet must not

exceed 100 watts.

• It is powered ON and OFF by the front panel STANDBY button or by

the AVR 4’s ON and OFF buttons.

13 7.1 CHANNEL INPUT

• Connect to the corresponding analog audio output of a

multichannel source component such as a DVD-Audio or

multichannel-SACD player or external multichannel decoder (disc

copy protected formats only allow analog signal transfer). Typically,

these sources will produce 5.1-channel output, in which case the

Surround Back jacks are left unconnected. The signal present at

these jacks can be heard by selecting Source 7 (7.1 CHANNEL INPUT

is defaulted to this Source).

• There is no bass-management or other processing (other than

master-volume control) available to this 7.1 channel input.

• While the multichannel audio output of a DVD/BD player can be

connected to these jacks, using the T 758’s own Dolby Digital and

DTS decoding and digital-analog converters via a digital connection

will usually produce superior results.

IDENTIFICATION OF CONTROLS

REAR PANEL

ENGLISHPORTUGUÊS FRANÇAISESPAÑOLITALIANODEUTSCHNEDERLANDSSVENSKAРУССКИЙ

NAD T 758 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von NAD T 758

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info