Bedienungsanleitung NAD T 758 (Seite 10 von 42) (Englisch)

745046

Zoom out

Zoom in

Vorherige Seite

1/42

Nächste Seite

14 AUDIO PRE-OUT

• The AUDIO PRE- OUT makes it possible to use the T 758 as a pre-

amplier to external power ampliers for some or all channels.

Connect FRONT L, FRONT R, CENTER, SURR R, SURR L, SURR-BL and

SURR-BR to the respective channel input of a power amplier or

ampliers driving the corresponding applicable speakers.

• Unlike the full range channels, there is no power amplier built-into

the T 758 for a subwoofer. Connect the SUBW output to powered

(“active”) subwoofers or to power amplier channels driving a

passive system.

ZONE 2

• SURR-BL and SURR-BR are also assigned as secondary ZONE 2 OUT.

This is applicable only if “Zone 2” is the selected setting of “Back

Amp” in the “Amplier Setup” menu. For further information, refer

to the item about ZONE CONTROLS at the USING THE T 758 - MAIN

MENU segment of the OPERATION section.

• Refer also to the item about ZONE 2 AT AUDIO PRE-OUT SURROUND

BACK in the ZONE CONTROLS segment of the OPERATION - USING

THE T 758 - MAIN MENU section.

NOTE

Never connect both the external amplier and T 758’s speaker outputs to

the same set of speakers.

15 ZONE 2

• Send zone selected audio source to the corresponding audio input

of a separately located additional amplier or receiver (not supplied)

that can power its matching set of speakers.

• Use high quality patch cables to reduce noise pickup over long

distance runs.

16 COMPONENT VIDEO INPUT 1-3, COMPONENT VIDEO MONITOR OUT

• Connect the Component Video Input to Component Video output

of compatible source components, typically a DVD player, BD

player, digital cable box or other applicable components. Connect

Component Video Monitor Out to the Component Video input of a

compatible video monitor/TV.

• Be sure to observe consistency in connecting the Y/Pb/Pr jacks

to the corresponding sources/inputs. The routing of the three

component video input is fully congurable via the Source Setup

item of the Setup Menu OSD.

• The T 758’s sets of component video input and output are fully

wideband and compatible with allowable HDTV formats.

17 SPEAKERS

• Connect the respective speaker’s FRONT L, FRONT R, CENTER,

SURR R, SURR L, SURR-BACK L, and SURR-BACK R channels to their

corresponding loudspeakers. Make sure the “+” (red) terminal and

“-” (black) terminal are connected to the corresponding “+” and “-”

terminals of the loudspeaker. Use extra care to ensure that no stray

wires or strands cross between posts or terminals at either end.

• SURR-BACK L and SURR-BACK R can be assigned as Zone 2 speaker

level output. This is applicable only if “Zone 2” is the selected setting

of “Back Amp” in the “Amplier Setup” menu. For further information,

refer to the item about ZONE CONTROLS at the USING THE T 758 -

MAIN MENU segment of the OPERATION section.

IDENTIFICATION OF CONTROLS

REAR PANEL

ENGLISH PORTUGUÊSFRANÇAIS ESPAÑOL ITALIANO DEUTSCH NEDERLANDS SVENSKA РУССКИЙ

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

NAD T 758 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von NAD T 758

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info