Bedienungsanleitung Netgear WAC505 (Seite 139 von 149) (Englisch)

710463

139

Zoom out

Zoom in

Vorherige Seite

1/149

Nächste Seite

• Make sure that the Ethernet cable connectors are securely plugged in at the access point and the

network device.

• Make sure that the connected network device is actually turned on.

• Make sure that you are using the correct Ethernet cable. Use a standard Category 5 Ethernet patch

cable. If the network device incorporates Auto Uplink™ (MDI/MDIX) ports, you can use either a crossover

cable or a normal patch cable.

Troubleshoot the WiFi Connectivity

If you are experiencing trouble connecting over WiFi to the access point, try to isolate the problem:

• Make sure that the WiFi settings in your WiFi device and access point match exactly.

For a device that is connected over WiFi, the WiFi network name (SSID) and WiFi security settings of

the access point and WiFi device must match exactly.

For information about accessing the access point for initial configuration over a WiFi connection, see

Connect to the Access Point for Initial Configuration on page 16.

• Does the WiFi device that you are using find your WiFi network?

If not, check the WLAN LEDs. If a WLAN LED is off, the associated WiFi radio is probably off too. For

more information about the WiFi radios, see Turn a Radio On or Off on page 51.

• If you disabled the access point’s SSID broadcast, your WiFi network is hidden and does not display in

your WiFi client’s scanning list. (By default, SSID broadcast is enabled.) For more information about the

SSID broadcast, see Set Up and Manage WiFi Networks on page 31.

• Does your WiFi device support the security that you are using for your WiFi network (WPA2-PSK or

WPA-PSK and WPA2-PSK). For more information, see Set Up and Manage WiFi Networks on page

31.

If you want to change the WiFi settings of the access point’s network, use a wired

connection to avoid being disconnected when the new WiFi settings take effect.

Tip

If your WiFi device finds your network but the signal strength is weak, check these conditions:

• Is your access point too far from your WiFi device or too close? Place your WiFi device near the access

point but at least 6 feet (1.8 meters) away and see whether the signal strength improves.

• Are objects between the access point and your WiFi device blocking the WiFi signal?

Troubleshoot Internet Browsing

If your computer or WiFi device is connected to the access point but unable to load any web pages from

the Internet, it might be for one of the following reasons:

• Your computer might not recognize any DNS server addresses.

A DNS server is a host on the Internet that translates Internet names (such as www addresses) to

numeric IP addresses. If you manually entered a DNS address when you set up the access point (that

is, the access point uses static IP address settings), reboot your computer and verify the DNS address.

Diagnostics and Troubleshooting

139

Insight Managed Smart Cloud Wireless Access Point WAC505 User Manual

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Netgear WAC505 Seite 139

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info