350-20081
4
EN nNiko sa I PM350-20081
Read the complete manual before carrying out the installation and activating the system. Keep the
manual for future reference.
1.
The presence or absence detector 360° (slave)
for surface mounting on high ceilings
consists of an
integral unit with on-off control of one channel and a motion sensor (PIR or passive infrared technology).
Y
4.2.).
The slave will control the lighting according to the parameters set on the master
refer to the manual supplied with the master
2.
2.1.
Danger: Disconnect all power before installing the detector
until installation has been completed.
Refer to the wiring diagram (fig. 1).
2.2.
Tip: Do not install the detector in the vicinity of heat sources such as stoves or electric heaters,
(ventilation systems) or any moving objects (fig. 2).
motion and heat in its surroundings. If the detector is installed in warehouses where closed trucks are used,
its operation may be less than optimal due to temperature differences that are too small.
Tip:
of 16 to 32 m on the ground (fig. 3).
The detector is suited for direct mounting on high ceilings (fig. 4).
At delivery
3.
3.1.
Using the two DIP switches you set the sensitivity of the motion sensor .
options:
the desired sensitivity
At delivery the motion sensor of this detector is set at the high sensitivity mode.
3.2.
Contrary to the master
activating the walking test (fig. 6).
The detection area is tested by activating the integrated motion sensor for the walking test :
1.
The blue indication LED lights up when you activate the test mode.
The lighting is switched on for five seconds and the red indication LED lights up each time the sensor
detects activity
up.
2.
If you forget to close the test mode, the detector will return to the selected settings after five minutes.
4.
4.1.
The detector should not be powered until all cables are connected.
be ready for use after approximately 40 seconds (warm-up time).
The red indication LED flashes during warm-up time.
LED will flash briefly twice.
4.2.
The detection area can be increased by adding an extra detector (slave) (350-20081).
slaves can be connected to one master (350-20080).
on the master
to 32 m).
overlap of approximately 30% (fig. 7).
If you would like to exclude motion detection in a portion of the detection area or if the detection area is too
large,
to 32 m.
5. MAINTENANCE
Dirt may prevent the detector from functioning properly
damp cloth and water with some detergent to clean the lens. Never exert pressure to wipe the lens clean.
the lens or other parts of the detector are defective,
6.
dimensions
45.9 x 117.3 mm (HxW)
64.1 x 117.3 mm (HxW) (including non-visible part)
power supply voltage 230
power consumption 0,2 W
mounting height (fig. 4 – 8 m
detection angle (fig. 360°
detection range (fig. circular
wire input 3 x 2,5 mm²
cable inlet on the side:
on the top:
protection degree IP54
protection class
class I devices
ambient temperature -5 – +50°C
quality mark CE marked in compliance with EN 60669-2-1
accessories presence or absence detector 360° (master) (350-20080)
7.
T
T
it sh
suppor
Du
t
each specific inst
t
This product complies with all of the relevant European guidelines and regulations. If applicable,
the EC declaration of conformity regarding this product at www.niko.eu.
8.
In case of doubt or for the specific exchange procedure in case of a possible defect, contact the Niko support
service in Belgium at +32 3 778 90 80 or your wholesaler/installer
be found at www.niko.eu under the
9.
T
of th
T
the def
In c
whi
Ni
use, incorrect operation, transformation of the product, maintenance that does not
inst
T
pro
chain stores, distributors, agents or permanent sales representatives, take priority over the above-mentioned
rules and
