• Installation Instructions
Please read these instructions carefully prior to
installation!
Installation should only carried out by persons
qualified
Incorrect
risk!
In
guarantee
Preparing for installation
1. T
installed on site - the included mains lead is
approx. 1 m long.
2. Check the stability of the door, retighten the
screws and nuts on the door
3. Check that the door is running smoothly and is
in good working order
bearings. Check the pretension of the springs
and, if necessary
4. Dismantle the existing door latches (bolt plate
and catches).
5. For garages without a second entrance, an
emergency release is required (accessory).
6. If a wicket door is included, fit the wicket door
contact.
7. Check the supplied screws and wall plugs to
ensure that these are suitable for the structural
conditions on site.
Required tools
- Drilling machine with 6 mm masonry drill
- Sturdy side cutter
- Wrench, sizes 13, 15 and 17 mm
- Slotted screwdriver
- Phillips screwdriver
Choosing the installation side
Choose
s c o s T s
installation
i F s i s
see .
Spray the track with silicone to achieve optimum
running
Fitting the toothed belt
The
Place
track (back 2a Slot
end
2b T
Feed
motor
2c Insert
track.
2d
Position
50
The
above
Finally
in
Fitting the rear toothed belt fastening
3a Feed the toothed
angle
Slot sleeve halves, as shown in 3b/3c , onto the
toothed
Attach knurled nuts 3d and turn to tension the
toothed
3e Make sure that you do not twist the toothed belt
in the process.
3f If the toothed belt overhangs, it can be
shortened.
Inserting the top track roller
4a 4b
0
1
25
2
3
4
4c track
screw
Fastening the door bracket
Place the door bracket on the designated drill holes
of
self-tapping
6a
and
6b Hold
door
construction
6c
clip.
Sliding block
Slot
the
with
Mains lead cable
The back of the control unit includes a chamber 8a ,
where, if required, the excess mains lead can be
stowed 8b.
Connecting the coiled cable
9a unit there
terminal
9b Insert red wire on left (1) and green wire on
right (2) into the terminal.
9c Insert plug (3) into designated socket and allow
to engage.
9d
Fastening the control unit
10a Install
distance
the
hole, insert
the
10b Align the unit and mark the remaining fixing
holes,
4.2 x 32.
W
Hold
maximum extension
may not exceed three times the original length.
Attach
against the
to
Connecting plan / aligning the aerial
Instructions: Do not connect any
current-carrying cables, only connect volt-
!
free push buttons and volt-free relay
outputs.
Where door systems are used by the
public or are impulse-operated out of sight
of the door
E. Connection for aerial
Route the aerial on the housing exit upwards.
When using an external aerial, the shielding
must be assigned to the adjacent terminal (F
right) 12b .
F12b
(accessories, e.g. key switch or digital coder)
G. Input STOP
Connection for safety devices
(accessories, e.g. wicket door contact).
An interruption at this input end causes the door
to stop during the opening or closing phase or
prevents the operator from starting up in either
direction. Connection for safety devices 12c
5
6
7
8
9
10
1
12
(accessories).
H. Input STOP
operator to automatically change direction
during the closing phase only
Connection for 2 wire light barrier EXTRA
12d (accessories).
Connection for an optical closing edge
protection OSE 12e .
I. V
Connection can take a max. load of 100 mA
(do not exceed!).
Connection for 24V signal lamp12f
(accessories). Connection for an external
receiver 12g (accessories).
J.
K. Connection for an external light, protected light
or signal lamp (protection classification II, max.
500W) 12h (accessories).
Lamp shade
13a The lamp shade conceals the terminal
connections. T
lamp shade underneath the guides of the control
unit.
13b Fasten the lamp shade with two self-tapping
screws 4.2 x 16.
Control elements
14a/b The control elements for programming the
door are located behind the white cover
The
Once
is 23.
A. The numerical display serves to indicate the
menu stage, the respectively set value and the
error/fault diagnosis.
a. The incremental display
readiness for operation and flashes on
acknowledgement of learned hand transmitter
codes.
B. During the setting / adjustment phase button
serves as an "UP" button and outside the menu
as a ST
C.
serves as a "DOWN" button.
D. serves to call up the settings /
adjustment menu, to change the menu stages
and store the settings.
Pr th c un i m
Pressing button
numbers
approx. 2 seconds, the display flashes and the
setting
selected setting is stored via button and the
programme
stage. By ,
stages
press until
the menu, button can be used to generate
impulse.
Menu stage 1: Programming the start
function
Briefly . “1”
the display flashes, press and keep pressed for
approx. 1
with wish
soon as the code has been read, the red point
display
Further
can
Menu stage 2: Programming the light
function
Figure
will
Press
Press key once again and figure 2 will be
13
14
15
16
Retain these installation, operating and maintenance instructions for the full duration of the operator
GB
