Bedienungsanleitung Novoferm NovoPort LED (Seite 19 von 43) (Deutsch, Englisch, Holländisch, Französisch, Spanisch)

709129

Zoom out

Zoom in

Vorherige Seite

1/43

Nächste Seite

• Operating Instructions

Information regarding the operating instructions

These operating instructions describe how to use the

product properly and safely. The safety advice and

instructions as well as the local health and safety

regulations and general safety regulations for the

range of use must be observed.

All persons using the door system must

be shown how to operate it properly and

safely.

- When the operator is being actuated, any

opening and closing phases must be

monitored.

- Keep hand transmitters out of the reach of

children.

- It must be ensured that neither persons nor

objects are located within the door's range of

travel.

• Functional sequence

The garage door operator can be actuated by push-

button on the control unit (figure 23) or by other

impulse generators, such as hand transmitters, key

switches etc. It is only necessary to generate a short,

sharp impulse.

- Initial impulse:

Operator starts up and causes the door to travel

to the set OPEN or CLOSE end-of-travel

positions.

- Impulse generated whilst the door is in motion:

Door stops

- A new impulse:

Door continues to move but in the opposite

direction.

• Internal safety device

If the closing door encounters an obstruction, the

operator stops and causes the door to open to its top

end-of-travel position in order to clear the

obstruction.

During the last 2 seconds of closing, the door only

opens slightly, this being sufficient to clear the

obstruction but otherwise preventing anyone from

being able to see inside the garage.

If the opening door encounters an obstruction, the

operator stops immediately. The door can be closed

again by generating a new impulse.

• External safety devices

- Wicket door contact STOP A

An open wicket door stops the operator

immediately or prevents it from starting up.

- Photocell defective (STOP B)

If the photocell is interrupted whilst the door is

closing, the door stops and reverses direction.

An interruption whilst the door is opening has no

effect.

• Quick release

When altering settings or making adjustments, in the

event of a power failure or malfunctions, the door can

be disengaged from the operator by actuating the

pull cord with knob on the lifting arm (figure 22a), so

that it can be operated manually.

To resume operation of the operator, press the lever

on the motor head (figure 22c) and the operator re-

engages.

If the door is to be operated manually over a longer

period of time, then the door latches which were

taken out of service for power operation, must be

refitted, otherwise the door will not be latched when

closed.

•

The lighting switches on automatically whenever a

start impulse is generated and switches off again

after the set time phase (factory setting approx. 90

seconds).

A second button on the hand transmitter can be

programmed for 4-minutes light (figure 16). When

the button on the hand transmitter is pressed, the

light switches on independent of the motor and

switches off again after approx. 4 minutes.

• Changing the light bulb

Pull out the mains plug and open the lamp shade

using a Phillips screwdriver size 2 x 100. Replace the

light shade (230 V, 40 W, cap E27) and screw the

lamp cover back on again.

• Signal light

If a signal light for signalling the opening and closing

phases is installed, this flashes together with the

lamp in the operator as soon as a start impulse is

generated. The operator starts with a time delay in

accordance with the set early warning phase (see

Special Settings in menu stage 7).

• Hand transmitters

- Programming further hand transmitters:

See menu stages 1 and 2 (figures 15 and 16).

- Changing the battery: slide back the battery

compartment cover on the hand transmitter.

Take out the battery.

- Insert a new battery. Be sure to pole correctly!

Slide the cover back on.

Empty batteries must be disposed of separately

(toxic waste)!

• Further operating modes

In menu 9, another operating mode can be chosen.

For the setting applying to menu 9, see parantheses.

•

Lighting

Normal operation for ventilation position (1)

The ventilation position is designed to allow

ventilation of the garage. For this, the door is opened

approx. 10 cm.

Actuation as for normal operation.

By pressing the 2 button on the hand transmitter or

generating an impulse via another device, the door

can be brought into the ventilation position from any

given position.

The gate will close automatically after 60 min or can

be closed earlier by any impulse transmitter.

Operation on a side-opening sectional door (2)

Instead of opening the door fully, the door can be

partially opened by approx. 1 m in order to provide

access to the garage.

By pressing the 2 button on the hand transmitter or

generating an impulse via another device, the door

can be brought into the partially open state from any

given position.

• Maintenance / Checks

For your own safety we recommend

that the door system be checked by a

specialist after initial installation and

then regularly at intervals of 1 year

minimum.

• Monitoring the force limit

The operator control unit features a dual-processor

safety system to monitor the force limit.

The integral force cut-out is automatically tested at

each end-of-travel position.

The door system must be checked before initial

operation and at least once a year thereafter, In the

process, the force limiting device (figure 20) must be

tested!

CAUTION! If the closing force is set too

high, this can result in injury to persons and

damage to property.

The opening force can be re-adjusted in menu stage

5, the closing force in menu stage 6.

Retain these installation, operating and maintenance instructions for the full duration of the operator’s service life!

Novoferm NovoPort LED Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info