Bedienungsanleitung Nuk Eco Control Video Display 550VD - 10749102 (Seite 13 von 36) (Englisch)

803238

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

data (see "9. Technical data" on

page 74).

This automatically switches the baby unit

on.

Note: You can also wall mount the baby unit

in a suitable position with the enclosed

screws. Make sure you position the screws

45 mm apart for this.

4.3 Connecting baby unit and

parent unit

Normally, a connection is automatically

established between the two units when

they are switched on:

1. Make sure that the two units are always

within range.

2. To switch the baby unit 1 on, press the

On/Off button 10. To do this, press and

hold the On/Off button until the power

LED 8 lights up.

3. To switch the parent unit 17 on, press the

On/Off button 32 and keep it depressed

until the LED 21 lights up green.

You will hear a beep, the "Hello" screen

will appear, and the parent unit will begin

searching for the connection signal of the

baby unit.

While the connection is being set up, the

connection indicator 20 will light up red.The

screen will remain white and show no video

picture.

The corresponding blue symbol will

appear on the screen of the parent

unit. 

As soon as the connection has been

established, the connection indicator 20

on the parent unit 17 and the VOX LED 7

on the baby unit 1 will light up green. The

connection symbol on the screen

disappears, and video transmission

starts.

If the connection setup is not successful

after 30 seconds the parent unit 17 will emit

a beep at regular intervals and the

connection indicator 20 will light up red.

The corresponding red symbol will

appear on the screen of the parent

unit to indicate that the connection

could not be set up.

4. First, check to be sure your baby is still

comfortable.

5. Then move the parent unit to a different

location within the range of the

connection signal so that a connection

can be set up successfully.

The parent unit and the baby unit will

automatically make repeated attempts to

connect until successful.

Note: If the connection indicator 20 begins

to flash green, this means that there is a

connection between the parent unit and the

baby unit, but your baby is currently asleep

and therefore the device has automatically

activated Eco-Mode to reduce the high-

frequency radio waves in baby’s room and

save energy.

Attention! While Eco-Mode is

active, video and sound

transmission is paused. The

screen will go white and the

corresponding symbol in the status bar will

show that Eco-Mode is active. The

connection between the two units remains

established, even while baby is sleeping.

4.4 Power supply

Baby unit

The power supply for the baby unit 1 works

only via the mains adapter. LED 8 lights up

green while the baby unit is on.

Parent unit

The parent unit 17 can be operated on

battery power with no mains connection for

up to 8 hours, or via the mains adapter, with

or without the battery inserted.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Nuk Eco Control Video Display 550VD - 10749102 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info