Bedienungsanleitung Nuk Eco Control Video Display 550VD - 10749102 (Seite 15 von 36) (Englisch)

803238

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

the device fails to detect a sound from your

baby for more than 20 seconds.

Note: At VOX level 5, the device is set to

continuous transmission. There is no Eco-

Mode at this level.

The connection indicator 20 flashes green

while Eco-Mode is active.

The screen will be white, as video

transmission is deactivated.

The appropriate symbol is shown

in the status bar in place of the

symbol that indicates the received

signal strength.

Deactivating Eco-Mode

Eco-Mode is deactivated when:

• your baby makes a sound that exceeds

your set sound limit (VOX level)

• you increase the VOX level setting to 5

(continuous transmission) (see

"6.8 Setting the VOX sensitivity level" on

page 62)

• you use the talk-back function (see

"6.15 Talk-back function" on page 72)

• you activate the lullabies (see

"6.11 Lullabies" on page 67)

Note: If VOX level 1 is set and the

lullabies are played at the lowest volume

setting, Eco-Mode can still be activated,

as the lullabies will not exceed the set

sound limit.

• you switch the nightlight on (see

"5.5 Nightlight" on page 54)

• you briefly press the On/Off button 10

When Eco-Mode is deactivated:

• the connection indicator 20 will show a

steady green light

• video and sound transmission will be

active again

• the status bar will show the received

signal strength symbol again instead of

the Eco-Mode symbol

Full-Eco-Control

The Full-Eco-Control function maintains the

connection between the parent unit and the

baby unit at all times, so that sounds, video,

and warnings (e.g. temperature alarm) can

be transmitted by the baby unit when

necessary.

The Full-Eco-Control function guarantees

that you and your baby are always

connected. Even when ECO mode is

activated, the baby unit will perform a link

check every 30 seconds to make sure that

the parent unit is still nearby and maintain

the connection between the two units.

If you are out of range at any time, the

parent unit will indicate this by changing the

colour of LED 20 to red and beeping.

A red warning symbol will appear on

the screen. 

Note: Check the range of your baby monitor

before using it.

5. Operating the baby unit

5.1 Switching the baby unit on

and off

The baby unit 1 will switch on automatically

as soon as you have connected the mains

adapter and plugged it into the power

supply. You can then switch the baby unit

off and back on as required.

• To switch the baby unit 1 on or off, press

and hold the On/Off button 10 until the

power LED 8 lights up or switches off.

5.2 Indicator LEDs

• The Power LED 8 lights up green while

the baby unit is switched on.

• The VOX LED 7 on the baby unit lights up

green when there is an established

connection between it and the parent unit.

• The VOX LED 7 will not be lit while the

baby unit 1 is switched to Eco-Mode or if

it was not possible to set up a connection

to the parent unit.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Nuk Eco Control Video Display 550VD - 10749102 Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info