Bedienungsanleitung Oki ES4161 (Seite 158 von 182) (Englisch)

492990

158

Zoom out

Zoom in

Vorherige Seite

1/182

Nächste Seite

Changing Network Settings From the Web Page

- 158 -

 Performing IPP Printing

Memo

 The following steps are explained using NotePad as an

example. The steps and menus may differ depending on

the application you use.

1 Open the file you want to print.

2 From the [File] menu, select [Print].

3 Select the IPP printer you created from

[Select Printer], and then click [Print].

Encrypting Communication by

IPSec

You can encrypt communication between your

computer and the machine.

The communication is encrypted by IPSec. When

IPSec is enabled, encryption is applied for all the

applications using IP protocols.

You can specify up to 50 hosts by their IP

addresses. When a host that is not registered

tries to access the machine, it is rejected. When

you try to access a host that is not registered,

the attempt is invalid.

Be sure to configure the machine in advance,

before configuring your computer.

Memo

 You must have a pre-shared key readied in advance.

Configuring Your Machine

In order to enable IPSec, your machine must first

be configured from the web page.

Note

 When you enable IPSec, the communication that is to and

from a host not specified in this procedure is rejected.

Memo

 Be sure to make a note of the values you specify in these

steps. They are necessary when you configure the IPSec

settings on your computer.

1 Access the machine's web page and log

in as the administrator.

2 Select [Admin Setup].

3 Select [Network Manager] >

[Security] > [IPSec].

4 Follow the on-screen instructions to

specify detailed settings.

Memo

 Either [ESP] or [AH] must be enabled in the

configuration for "Phase2 Proposal".

5 Click [Send].

The network card reboots to enable the new

settings.

Note

 If you were unable to set up IPSec because of an

inconsistency between the parameters that were specified,

you will be unable to access the web page. In this case,

either disable IPSec from the control panel of the machine,

or initialize the network settings.

Configuring Your Computer

Memo

 Be sure to configure the machine in advance, before

configuring your computer.

1 Click [Start] and select [Control Panel]>

[

System and Security

]> [

Administrative

Tools].

2 Double-click [Local Security Policy].

3 On the [Local Security Policy] window,

click [IP Security Policy (Local

Computer)].

4 From the [Action] menu, select [Create

IP Security Policy].

5 On the [IP Security Policy Wizard],

click [Next].

6 Enter a [Name] and a [Description]

and then click [Next].

7 Select the [Activate the default

response rule (earlier versions of

Windows only)] check box and then

click [Next].

8 Select [Edit Properties] and then click

[Finish].

9 On the IP security policy properties

window, select the [General] tab.

10 Click [Settings].

11 On the [Key Exchange Settings]

window, enter a value (minutes) for

[Authenticate and generate a new

key after every].

Note

 Specify the same value as [Lifetime] specified in the

configuration for "Phase1 Proposal" in "Configuring

Your Machine". Although [Lifetime] is specified in

seconds, enter a value in minutes for this step.

12 Click [Methods].

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Oki ES4161 Seite 158

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Oki ES4161

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info