Bedienungsanleitung Olivetti ECR 2100 Euro (Seite 22 von 64) (Englisch)

624806

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

ENGLISH

NOTE: Program all the desired features at the same time in order to

create a single receipt of all selections. Keep the receipt in a

safe place for future reference.

Making Changes to Cash RegMaking Changes to Cash Reg

Making Changes to Cash Reg

ister Prister Pr

ister Pr

ogrammingogramming

ogramming

Once the cash register is programmed to satisfy your specific needs,

there is no need to reprogram the entire machine to make single

program changes or corrections. If you wish to make a change (such as

an update to VAT rates, PLUs or Euro exchange rates), be sure you are

in the program mode, re-do the program in question and finalize when

you are ready to exit the programming mode. A new program entry will

automatically overwrite a previous entry for the same program.

EnterEnter

Enter

ing the Pring the Pr

ing the Pr

ogram Modeogram Mode

ogram Mode

To enter into the program mode, unlock, open and remove the printer

compartment cover and then slide the control switch to the PRG

position. Refit the printer compartment cover.

Exiting the PrExiting the Pr

Exiting the Pr

ogram Modeogram Mode

ogram Mode

To exit the program mode, open the printer compartment cover and

slide the control switch to the R1 or R2 position if you wish to carry out

sales transactions, to the X or Z position if you wish to take

management reports, or to the OFF position if you wish to exit.

ClearClear

Clear

ing Erring Err

ing Err

oror

To clear an error made during the programming phase, simply press

the [C] key. The error tone ends, the display clears and the keypad

unlocks.

If the message "SEC Code" is displayed, this means that a PRG and Z

mode security password was programmed. Enter the 4-digit code

followed by the [Charge] key to continue.

In case an error condition cannot be cleared, perform one of the two

general clearance methods explained in the section entitled General

Clearance. Remember that the second general clearance sets all

counters and totals to zero, and cancels all features programmed.

ClerCler

Cler

k Numberk Number

k Number

s and Secrs and Secr

s and Secr

et Codeset Codes

et Codes

Clerk codes are a special security feature to control access to the

secret entry codes of three digits each.

PrPr

ogramming a Secrogramming a Secr

ogramming a Secr

et Code Linket Code Link

et Code Link

ed to a Clered to a Cler

ed to a Cler

NumberNumber

Number

1. Open the printer compartment and slide the control switch to the

PRG position.

2. Activate the clerk system by typing [44444] followed by [1] and

then pressing the [Amt Tend/TOTAL] key.

3. Type [444444] and press the [Amt Tend/TOTAL] key.

4. Type a number to identify the clerk which the secret code will be

linked.

5. Set a three-digit secret code by typing three [numeric keys].

6. Press the [Clerk] key.

Repeat the above operations (from step 3 to step 6) to assign a secret

code to the remaining 5 Clerks or use the [C] key to exit from Clerk

Secret Code programming.

If you wish to change the clerk's secret code and the Clerk system is

already activated, there is no need to perform step 2 above.

Example: Assign secret code 106 to Clerk 1 for the first time.

Type/Press:

[44444] + [1] + [Amt Tend/TOTAL] + [444444] + [Amt Tend/TOTAL]

+ [1106] + [Clerk]

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Olivetti ECR 2100 Euro Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info