Bedienungsanleitung Onkyo HT-R990 (Seite 40 von 172) (Englisch, Französisch)

462101

Zoom out

Zoom in

Vorherige Seite

1/172

Nächste Seite

You can display various information about the current

input source as follows. (Components connected to the

UNIVERSAL PORT jack are excluded.)

The following information can typically be displayed.

If the input signal is analog, “Analog” is displayed. If the

input signal is PCM, the sampling frequency is displayed. If

the input signal is digital but not PCM, the signal format is

displayed. Information is displayed for about three seconds,

then the previously displayed information reappears.

When you connect an

-capable Onkyo component, you

must configure the input display so that

can work properly.

This setting can be done only from the front panel.

You can temporarily mute the output of the AV receiver.

This section explains how to record the selected input

source to a component with recording capability, and how

to record audio and video from different sources.

AV Recording

Audio sources can be recorded to a recorder (e.g., cassette

tape deck, CDR, MD recorder). Video sources can be

recorded to a video recorder (e.g., VCR, DVD recorder).

Displaying Source Information

Press RECEIVER followed by DISPLAY

repeatedly to cycle through the available

information.

Tip

• Alternatively, you can use the AV receiver’s DISPLAY.

Changing the Input Display

Press TV/CD, GAME or VCR/DVR.

“TV/CD”, “GAME” or “VCR/DVR” appears on the

display.

Press and hold down TV/CD, GAME or VCR/DVR

(about 3 seconds) to change the input display.

Repeat this step to select the desired input display.

■ TV/CD:

■ GAME:

■ VCR/DVR:

Note

• DOCK can be selected for the TV/CD, GAME or

VCR/DVR input selector, but not at the same time.

• Enter the appropriate remote control code before using the

remote controller for the first time (➔ page 64).

Input source

Input signal

resolution

Output

resolution

Signal format

Listening mode

Sampling

frequency

TV/CD → DOCK

→

TAPE

GAME ↔ DOCK

VCR/DVR ↔ DOCK

Muting the AV Receiver

Press RECEIVER followed by MUTING.

The output is muted and the MUTING indicator

flashes on the display.

Tip

• To unmute, press MUTING again or adjust the volume.

• Muting is automatically cancelled when the AV receiver is

set to standby.

Using Headphones

Connect a pair of stereo headphones with a

standard plug (1/4 inch or 6.3 mm) to the

PHONES jack.

Note

• Always turn down the volume before connecting your

headphones.

• While the headphones plug is inserted in the PHONES

jack, the speakers are turned off. (The Powered Zone 2

speakers are not turned off.)

• When you connect a pair of headphones, the listening mode

is set to Stereo, unless it’s already set to Stereo, Mono, or

Direct.

• If you connect an iPod or iPhone to the USB port on this

device, no sound will be output from the headphones jack.

Recording

Use the input selector buttons to select the source

that you want to record.

You can watch the source while recording. The AV

receiver’s MASTER VOLUME control has no effect

on recording.

On your recorder, start recording.

On the source component, start playback.

If you select another input source during recording,

that input source will be recorded.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Onkyo HT-R990 Seite 40

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Onkyo HT-R990

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info