Bedienungsanleitung Onkyo TX-DS494 (Seite 22 von 36) (Englisch)

553751

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

Selecting a sound source

1. Press the desired input selector button.

The selected source name appears in the display.

If the TAPE button is pressed, either the TAPE or MD input

which has been selected beforehand will be displayed. The

TAPE and MD sources can be switched alternately by holding

the TAPE button for about 2 seconds.

2. When the selected source is other than FM, AM

or PHONO, press the AUDIO SELECTOR button

on the front panel or the AUDIO SEL button on

the remote controller to select an audio input

signal format.

Each time the button is pressed, the setting cycles; “AUTO”

→

“MULTI CH”

→

“ANALOG”

→

“AUTO” (back to the

beginning) (refer to page 23).

3. Make sure that the

SPEAKERS A indicator lights

up in the display.

If it does not light, press the SPEAKERS A button.

4. Start playing the selected input source.

Follow the operating instructions for the source device.

5. Adjust the volume with the MASTER VOLUME

dial on the front panel or the VOLUME 5/∞

buttons on the remote controller.

Turn the MASTER VOLUME dial clockwise to increase the

volume or counterclockwise to decrease it.

6. Adjust the tone with the BASS and TREBLE

control knobs on the front panel.

Turn the BASS and TREBLE control knobs to adjust the bass

and treble response from the Front speakers (refer to page 8).

Note:

If you hear no sound from the speakers, check the following items:

• Make sure that all devices and speakers are connected

correctly and securely.

• The sound is muted when the MUTING indicator flashes.

Press the MUTING button on the remote controller to cancel

the mute function (refer to page 23).

• When you select a source that is connected to the DIGITAL

INPUT jacks on the rear panel, you must select digital input

(refer to page 12).

STANDBY/ON

OFF

POWER

PHONES

MASTER VOLUME

BASS

TREBLE

RECEIVER

494

PHONO

TAPE

VIDEO

DVD

ABSPEAKERS

DIMMER

SURROUND

DTS/

VIDEO

VCR

AUDIO

SELECTOR

LISTENING MODE

DSP

STEREO

DISPLAY

STANDBY

SP SEL TUNING PRESET

MEMORY

MODE

DIGITAL

INPUT

MODE

CLEAR

INPUT SELECTOR

MODE

SLEEP DIMMER DISPLAY

CD TAPE PHONO TUNER

D V D VIDEO 1 VIDEO 2

SUR MODE

SW MODE AUDIO SEL

TUNER

PRESET

STANDBY/ ON

DISC

MUTING

DVD CD TAPE

VOLUME

TOP MENU

CH SEL

RETURN

SETUP

TEST TONE

LEVEL

ENTER

VOLUME 5/∞

SPEAKERS A

AUDIO SELECTOR

LEVEL 5/∞

AUDIO SEL

MUTING

CH SEL

TEST TONE

SLEEP

Input selector

INPUT

SELECTOR

BASS/TREBLE

MASTER VOLUME

Using MULTI CHANNEL INPUT

The MULTI CHANNEL INPUT refers to a system, which is

compatible with a source component equipped with 5.1-channel

outputs (DVD player, MPEG decoder, etc.), reproducing the left/

right front, center and left/right surround channels from five

respective speakers and outputting the subwoofer channel from

SUB WOOFER PRE OUT (refer to page 11).

1. Press AUDIO SELECTOR button repeatedly to

select “MULTI CH”.

2. Turn on the component connected to the MULTI

CHANNEL INPUT port and start playing the

desired media.

3. If necessary, press the CH SEL button on the

remote controller to select an individual

speaker. Then press the LEVEL 5/∞ button to

adjust the output level as desired.

Adjust the speaker output level so that you can hear the same

sound level from each speaker at the listening position. For the

front right, front left, center, surround right and surround left

speakers, the output levels can be adjusted between –12 to +12

dB. The subwoofer can be adjusted between –30 to +12 dB.

The volume levels from the speakers reproducing MULTI

CHANNEL INPUT are independent from the speaker levels

set using the test tone (page 21). These settings are not applied

to speakers reproducing MULTI CHANNEL INPUT.

Notes:

• MULTI CH cannot be selected when FM, AM or PHONO is

selected as the input source.

• The surround mode cannot be selected when MULTI CH is

selected. Also, if MULTI CH is selected during use of a

surround mode, it is canceled automatically.

• If the speaker level is set to +1 dB or higher, the maximum

level indicated in the display will change if you raise the

volume level.

• Regardless of the speaker configuration, the input signal will

be output to each corresponding speaker. For example, even if

the speaker configuration is set to 2 ch, sound comes from all

speakers.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Onkyo TX-DS494 Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Onkyo TX-DS494

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info