Bedienungsanleitung Onkyo TX-DS494 (Seite 23 von 36) (Englisch)

553751

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

Selecting a sound source

Setting the input signal format

If the input source is DVD, CD, VIDEO 1, VIDEO 2 or TAPE, you

can specify the input signal format.

With the initial setting, AUTO is assigned to the DVD, CD and

VIDEO 1 inputs, and ANALOG is assigned to the TAPE and

VIDEO 2 inputs. You can change this according to the signal

format of the input source.

For example, follow the steps below to specify the input signal

format for the VIDEO 2 input:

1. Press the VIDEO 2 button.

VIDEO 2 is selected as the input source and “VIDEO 2”

appears in the display.

2. Press the AUDIO SELECTOR button.

The current setting is displayed.

Press the AUDIO SELECTOR button repeatedly

until the desired input signal format is displayed.

Each press of the button switches the displayed input format as

follows. AUTO is skipped when the selected input is not

assigned to the DIGITAL INPUT jacks (refer to page 12).

After 5 seconds, the original display appears and the setting is

completed.

Notes:

• With ANALOG setting, even if a digital signal is input from

the same component, only the analog signal will be output.

• When a digital input setting is changed while an input signal

format other than MULTI CH is set, the digital input becomes

automatically ANALOG if it has been “– – – – –” or “AUTO”

if it has been “OPT”, “COAX 1” or “COAX 2”.

Sleep function (Remote controller only)

The sleep timer can turn off the power to the system after a

specified time period.

Press the SLEEP button on the remote controller.

The SLEEP indicator will light and “SLEEP 90 MIN” (the

TX-DS494 will turn off after 90 minutes) appears in the display.

• Pressing the SLEEP button each time reduces the time value in

10-minute increments.

• To cancel the sleep function, press the SLEEP button when the

time displayed is less than 10 minutes.

• While the sleep function is enabled, you can press the SLEEP

button to see how much time is left.

Mute function (Remote controller only)

The muting function can turn down the playback sound

immediately. This can useful, for example, when you receive a

telephone call while listening to music or another source.

Press the MUTING button on the remote controller.

The MUTING indicator will flash and the sound from the speakers

or headphones will be switched off by the receiver’s audio muting

circuits.

Press the MUTING button again to turn the sound back on.

Note:

The mute function will be cancelled if you turn off the TX-DS494.

Select this setting to play a digital

signal. When a digital signal is not

input, the analog signal is played.

Select this setting to play back the

input from a source component

connected to an audio input jack.

Select this setting to play back the

input from the component connected

to the MULTI CHANNEL INPUT port.

MUTING

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Onkyo TX-DS494 Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Onkyo TX-DS494

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info