Bedienungsanleitung Onkyo TX-NR3008 (Seite 82 von 116) (Englisch)

553767

Zoom out

Zoom in

Vorherige Seite

1/116

Nächste Seite

Connecting Your Zone 3 Speakers to an

Amp in Zone 3

This setup allows 9.2-channel playback in your main lis-

tening room and 2-channel stereo playback in Zone 3,

with a different source in each room.

Note

• With the default settings, the Zone 3 volume must be set on the

Zone 3 amp. If your Zone 3 amp has no volume control, set the

“Zone 3 Out” setting to “Variable” so that you can set the

Zone 3 volume on the AV receiver (➔ 83).

Zone 3 12V Trigger

When Zone 3 is turned on, the output from the ZONE 3

12V TRIGGER OUT goes high (+12 volts, 25 milliam-

peres max). Connecting this jack to a 12-volt trigger input

on a component in Zone 3 will make that component turn

on or off as and when Zone 3 is turned on or off on the AV

receiver.

If you’ve connected your Zone 2/3 speakers to the AV

receiver, as explained in “Connecting Your Zone 2 Speak-

ers Directly to the AV receiver” (➔ 80) or “Connecting

Your Zone 3 Speakers Directly to the AV receiver”

(➔ 81), you must set the “Powered Zone 2” or “Powered

Zone 3” setting to “Act” (Activated).

Note

• Powered Zone 2 cannot be used if “Speakers Type(Front B)”

setting set to “Normal”, “Bi-Amp” or “BTL” (➔ 51).

• Powered Zone 3 cannot be used if “Speakers Type(Front A)”

or “Speakers Type(Front B)” setting set to “Bi-Amp” or

“BTL” (➔ 51).

• These setting cannot be used if the “Front High + Front Wide”

setting is set to “Yes”.

• This procedure can also be performed on the AV receiver by

using SETUP, arrows, and ENTER.

Hookup

• Use an RCA audio cable to connect the AV receiver’s

ZONE 3 PRE OUT L/R jacks to an analog audio input on

your Zone 3 amp.

• Connect your Zone 3 speakers to the speaker terminals on

your Zone 3 amp.

Main room

Zone 3

AV receiver

Receiver/

integrated amp

Setting the Powered Zone 2/3

Press RECEIVER followed by SETUP.

The main menu appears onscreen.

Tip

• If the main menu doesn’t appear, make sure the appropri-

ate external input is selected on your TV.

Use q/w to select “Speaker Setup”, and then press

ENTER.

The “Speaker Setup” menu appears.

Use q/w to select “Speaker Settings”, and then

press ENTER.

The “Speaker Settings” menu appears.

Use q/w to select “Powered Zone 2” or “Powered

Zone 3”, and use e/r to select:

` Not Act

FRONT WIDE/ZONE 2 L/R or SURR

BACK/ZONE 3 L/R speaker terminals not

activated (Powered Zone 2/3 disabled).

` Act:

FRONT WIDE/ZONE 2 L/R or SURR

BACK/ZONE 3 L/R speaker terminals acti-

vated (Powered Zone 2/3 enabled).

Press SETUP.

The setup menu closes.

2. Speaker Setup

1. Speaker Settings

2. Speaker Configuration

3. Speaker Distance

4. Level Calibration

5. Equalizer Settings

6. THX Audio Setup

2–1. Speaker Settings

Speaker Impedance

Speakers Type(Front A)

Speakers Type(Front B)

Powered Zone 2

Powered Zone 3

6ohms

Normal

Not Use

Not Act

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Onkyo TX-NR3008 Seite 82

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Onkyo TX-NR3008

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info