Bedienungsanleitung Onkyo TX-NR3008 (Seite 83 von 116) (Englisch)

553767

Zoom out

Zoom in

Vorherige Seite

1/116

Nächste Seite

Note

• This procedure can also be performed on the AV receiver by

using SETUP, arrows, and ENTER.

■ Zone 2 Out, Zone 3 Out

` Fixed

The Zone 2/3 volume must be set on the amp in that

zone.

` Variable:

The Zone 2/3 volume can be set on the AV receiver.

If you’ve connected your Zone 2/3 speakers to an amp

with no volume control, set the “Zone 2 Out” and

“Zone 3 Out” setting, respectively, to “Variable” so that

you can set the volume, balance, and tone of Zone 2/3 on

the AV receiver.

■ Zone 2 Maximum Volume,

Zone 3 Maximum Volume

` Off

, 50 to 99 (Absolute display)

` Off

, –32dB to +17dB (Relative display)

With this setting, you can limit the maximum volume for

Zone 2/3.

■ Zone 2 Power On Volume,

Zone 3 Power On Volume

` Last

, Min, 1 to 99 or Max (Absolute display)

` Last

, –QdB, –81dB to +18dB (Relative display)

This setting determines what the volume will be for

Zone 2/3 each time the AV receiver is turned on.

To use the same volume level as when the AV receiver was

last turned off, select “Last”.

The “Zone 2 Power On Volume” and “Zone 3 Power On

Vol ume ” cannot be set higher than the “Zone 2 Maxi-

mum Volume” and “Zone 3 Maximum Volume” setting.

This section explains how to turn Zone 2/3 on and off,

how to select an input source for Zone 2/3, and how to

adjust the volume for Zone 2/3.

Controlling Zone 2/3 from the AV receiver

Note

• When Zone 2/3 is turned off, the output from the ZONE 2/3

12V TRIGGER OUT goes low (0 volts).

Setting the Multi Zone

Press RECEIVER followed by SETUP.

The main menu appears onscreen.

Tip

• If the main menu doesn’t appear, make sure the appropri-

ate external input is selected on your TV.

Use q/w to select “Hardware Setup”, and then

press ENTER.

The “Hardware Setup” menu appears.

Use q/w to select “Multi Zone”, and then press

ENTER.

The “Multi Zone” menu appears.

Use q/w to select an item, and use e/r to change

it.

The items are explained below.

Press SETUP.

The setup menu closes.

7. Hardware Setup

1. Remote ID

2. Multi Zone

3. Tuner

4. HDMI

5. Auto Power Down

6. Network

7. Firmware Update

7-2. Multi Zone

Zone 2 Out

Zone 2 Maximum Volume

Zone 2 Power On Volume

Zone 3 Out

Zone 3 Maximum Volume

Zone 3 Power On Volume

Fixed

Off

Last

Fixed

Off

Last

Using Zone 2/3

To turn on Zone 2/3 and select an input source,

press ZONE 2 or ZONE 3 followed by an input

selector button within 8 seconds.

Zone 2/3 turns on, the ZONE 2/3 indicator lights.

Tip

• ZONE 2/3 12V TRIGGER OUT goes high (+12 V).

To select AM or FM, press TUNER input selector

and ZONE 2 or ZONE 3 repeatedly.

(North American models) You can also select SIR-

IUS.

To select the same source as that of the main room,

press ZONE 2 or ZONE 3 twice. “Zone 2 Selector:

Source” or “Zone 3 Selector: Source” appears on

the display.

To turn off Zone 2/3, press ZONE 2 or ZONE 3.

ZONE 2 or ZONE 3 indicator flashes.

Press OFF.

The zone is turned off, and the ZONE 2 or ZONE 3

indicator goes off.

ZONE 3

ZONE 2

OFF

ZONE 2 indicator

ZONE 3 indicator

Input selector buttons

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Onkyo TX-NR3008 Seite 83

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Onkyo TX-NR3008

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info