Bedienungsanleitung Onkyo TX-NR3008 (Seite 84 von 116) (Englisch)

553767

Zoom out

Zoom in

Vorherige Seite

1/116

Nächste Seite

Controlling Zone 2/3 with the Remote

Controller

Note

• To control Zone 2/3, you must press the remote controller’s

ZONE first.

• ZONE turns red while Zone 2 is on, and green while Zone 3 is

on.

Note

• Only analog input sources are output by the ZONE 2/3 PRE

OUT and FRONT WIDE/ZONE 2 L/R, SURR BACK/ZONE

3 L/R terminals. Digital input sources are not output. If no sound

is heard when an input source is selected, check if it’s connected

to an analog input.

• You cannot select different AM or FM radio stations for your

main room and Zone 2/3. The same AM/FM radio station will be

heard in each room. For example, if you have an FM station for

the main room, that station will also be used in Zone 2.

• When you connect Zone 3 speakers directly to the AV receiver,

listening modes that require surround back speakers such as

Dolby EX, DTS-ES or THX Surround EX are unavailable.

• When the input selector of Zone 2/3 is selected, power consump-

tion on standby mode slightly increases.

• While Zone 2/3 is on, u functions will not work.

Adjusting the Volume for Zones

Muting Zones

Adjusting the Tone and Balance of Zones

Note

• Zones can also be unmuted by adjusting the volume.

• The Zone 2 volume, tone, and balance function have no effect on

ZONE 2 PRE OUT when the “Zone 2 Out” setting is set to

“Fixed” (➔ 83) and “Powered Zone 2” setting is set to “Not

Act” (➔ 82).

• The Zone 3 volume, tone, and balance function have no effect on

ZONE 3 PRE OUT when the “Zone 3 Out” setting is set to

“Fixed” (➔ 83) and “Powered Zone 3” setting is set to “Not

Act” (➔ 82).

• Even if you repeatedly press the remote controller’s ZONE to

select zones, the last zone selection will be retained once you

have switched to other components by pressing other REMOTE

MODE after pressing ZONE.

Press ZONE repeatedly, then point the remote

controller at the AV receiver and press ON.

Tip

•The ZONE 2/3 12V TRIGGER OUT goes high (+12 V).

To select an input source for Zone 2/3, press

ZONE repeatedly, followed by INPUT SELEC-

TOR.

To select AM or FM, press TUNER input selector

and ZONE repeatedly.

(North American models) You can also select SIR-

IUS.

To turn off Zone 2/3, press ZONE repeatedly, fol-

lowed by STANDBY.

INPUT

SELECTOR

ZONE

STANDBY

On the remote controller, press ZONE repeatedly,

and then use VOL q/w.

On the AV receiver, press ZONE 2 or ZONE 3

(the ZONE 2/3 indicator and Zone 2/3 selector on

the display flashes) and press LEVEL followed by

Up r/Down e within 8 seconds.

On the remote controller, press ZONE repeatedly,

and then press MUTING.

To unmute a zone, on the remote controller, press

ZONE, and then press MUTING again.

On the AV receiver, press ZONE 2 or ZONE 3.

Press the AV receiver’s TONE repeatedly to select

“Bass”, “Treble” or “Balance”.

Use e/r to adjust the bass, treble or balance.

• You can boost or cut the bass or treble from –10 dB

to +10 dB in 2 dB steps.

• You can adjust the balance from 0 in the center to

+10 dB to the right or +10 dB to the left in 2 dB

steps.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Onkyo TX-NR3008 Seite 84

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Onkyo TX-NR3008

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info