Bedienungsanleitung Onkyo TX-NR3010 (Seite 55 von 168) (Englisch)

492661

Zoom out

Zoom in

Vorherige Seite

1/168

Nächste Seite

Turning On & Basic Operations

En-55

The Whole House Mode is useful when you want to add

extra background music to your home party; this allows

you to enjoy the same stereo music as the main room in

separate rooms (Zone 2/3).

The Whole House Mode selects the same input source for

Multi Zone as the main room’s.

See also:

• “Speaker Setup” (➔ page 66)

• “Multi Zone” (➔ page 87)

You can set which speakers you want to use by priority.

You can temporarily mute the output of the AV receiver.

Using the Whole House Mode

Press WHOLE HOUSE MODE on the front panel.

To cancel the Whole House Mode, change the input

source for the main room or select a listening mode

(➔ page 45).

Note

• The Whole House Mode only supports analog audio.

• To adjust the volume of Multi Zone, switch the AV receiver

to Multi Zone control. See “Adjusting the Volume for

Zones” (➔ page 89) for the volume adjustment of Multi

Zone.

• The Whole House Mode is not available in the following

cases:

–The “Audio TV Out” setting is set to “On”

(➔ page 84).

–“HDMI Control(RIHD)” is set to “On” (➔ page 83)

and you’re listening through your TV speakers.

– Digital Processing Crossover Network is used

(➔ page 71).

Selecting Speaker Layout

Press RECEIVER followed by SP (speaker layout)

repeatedly to select:

■ 9.2 ch playback

` Speaker Layout:SB/FH:

The sounds from surround back and front high

speakers are output by priority.

` Speaker Layout:SB/FW:

The sounds from surround back and front wide

speakers are output by priority.

` Speaker Layout:FH/FW:

The sounds from front high and front wide

speakers are output by priority.

Note

• This setting is not available in either of the following cases:

–The “Speakers Type(Front A)” setting is set to

“Bi-Amp” or “Digital Crossover”.

– Speakers B is being used.

–The “Powered Zone 2/3” setting is set to “Yes” and

Zone 2/3 is turned on.

• Playback conditions may be limited depending on the set-

tings in “Speaker Settings” (➔ page 66) and “Speaker

Configuration” (➔ page 67).

• When a listening mode which doesn’t support front high,

front wide or surround back speakers is used, this setting

cannot be selected.

Important:

• The following layouts are only available when the “11ch

Playback” is set to “No” (➔ page 66) and all

corresponding speakers are enabled.

■ Speakers A or Speakers B Configuration

When “Speakers Type(Front B)” setting is set to

other than “No”, the relevant speaker indicator

lights (A or B), and you can choose a speaker layout

between Speakers A and Speakers B. Speakers A or

B can be switched regardless of listening modes.

Note

• When using Speakers B, you cannot use front wide

speakers.

• While using Speakers B, you cannot use

Audyssey MultEQ

XT32 Room Correction and Speaker

Setup, as well as Audyssey Dynamic EQ

and

Audyssey Dynamic Volume

Muting the AV Receiver

Press RECEIVER followed by MUTING.

The output is muted and the MUTING indicator

flashes on the AV receiver’s display.

Tip

• To unmute, press MUTING again or adjust the volume.

• Muting is automatically cancelled when the AV receiver is

set to standby.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Onkyo TX-NR3010 Seite 55

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Onkyo TX-NR3010

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info