Bedienungsanleitung Onkyo TX-NR3010 (Seite 106 von 168) (Englisch)

492661

106

Zoom out

Zoom in

Vorherige Seite

1/168

Nächste Seite

Appendix

En-106

■ When performing Automatic Speaker Setup, the

measurement fails and the message “Ambient

noise is too high.” is displayed.

■ The following settings can be made for the

composite video inputs

You must use the buttons on the unit to make these

settings.

On the AV receiver, press the input selector for the input

source that you want to set and the SETUP button

simultaneously. While holding down the input selector

button, press SETUP until “Video ATT :On” appears

on the AV receiver’s display. Then, release both buttons.

To turn the setting off, repeat the above process so that

“Video ATT :Off” appears on the AV receiver’s

display, and release the buttons.

• Video Attenuation

This setting can be made for the BD/DVD, CBL/SAT,

STB/DVR, GAME 1, AUX, or USB input.

If you have a game console connected to the composite

video input, and the picture isn’t very clear, you can

attenuate the gain.

Video ATT :Off: The gain is not changed (default).

Video ATT :On: The gain is reduced by the values

specified below.

– 2 dB for the ZONE 2 OUT V and HDMI output.

– 6 dB for the MONITOR OUT V output.

Note

• With the USB input selector, this setting is only available when

an iPod/iPhone is connected and set to Extended Mode (Video)

or Standard Mode.

■ If the picture on your TV/monitor connected to

the HDMI output is unstable, try switching the

DeepColor function off

To turn off the DeepColor function, simultaneously

press the STB/DVR and 8ON/STANDBY buttons on

the AV receiver. While holding down STB/DVR, press

8ON/STANDBY until “Deep Color:Off” appears on

the AV receiver’s display. Then, release both buttons.

To reactivate the DeepColor function, repeat the above

process until “Deep Color:On” appears on the AV

receiver’s display and release the buttons.

The AV receiver can upconvert component video and

composite video sources for display on a TV connected to

the HDMI output. However, if the picture quality of the

source is poor, upconversion may make the picture worse

or disappear altogether.

In this case, try the following:

Tip

• To by-pass the upconversion, set the “Picture Mode” setting to

“Direct” (➔ page 78).

This can be caused by a malfunction in your speaker

unit. Check if the unit produces normal sounds.

—

The AV receiver contains a microcomputer for signal

processing and control functions. In very rare situations,

severe interference, noise from an external source, or

static electricity may cause it to lockup. In the unlikely

event that this happens, unplug the power cord from the

wall outlet, wait at least five seconds, and then plug it

back in.

Onkyo is not responsible for damages (such as CD rental

fees) due to unsuccessful recordings caused by the unit’s

malfunction. Before you record important data, make

sure that the material will be recorded correctly.

Before disconnecting the power cord from the wall

outlet, set the AV receiver to standby.

Important Note Regarding Video Playback

If the video source is connected to a component

video input, connect your TV to COMPONENT

VIDEO MONITOR OUT.

If the video source is connected to a composite video

input, connect your TV to MONITOR OUT V.

On the main menu, select “Input/Output Assign”,

and then “Component Video Input” (➔ page 65).

If the video source is connected to COMPONENT

VIDEO IN 1, select the relevant input selector, and

assign it to “IN1”.

If the video source is connected to COMPONENT

VIDEO IN 2, select the relevant input selector, and

assign it to “IN2”.

If the video source is connected to a composite video

input, select the relevant input selector, and assign it to

“-----”.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Onkyo TX-NR3010 Seite 106

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Onkyo TX-NR3010

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info