Bedienungsanleitung Onkyo TX-NR3010 (Seite 109 von 168) (Englisch)

492661

109

Zoom out

Zoom in

Vorherige Seite

1/168

Nächste Seite

Appendix

En-109

The AV receiver allows you to update the firmware using a

USB device.

Note

• Never unplug or turn off the AV receiver during the update

process.

• Never plug or unplug an HDMI cable or a USB device during the

update process.

• Never unplug the USB storage device containing the firmware

file or the AC power cord during the update process.

• Do not attempt to access the AV receiver from your PC while it

is being updated.

• It takes up to 60 minutes to complete the firmware update.

• The AV receiver will retain all your settings after the update is

finished.

Before Starting

•Set the “HDMI Control(RIHD)” setting to “Off”

(➔ page 83).

• Turn off the controller device connected via RS232 and

network.

• Turn off Multi Zone if this function is present.

• Stop playback of contents from Internet Radio,

iPod/iPhone, USB or servers, etc.

• If there is any data in the USB device, remove it first.

Update Procedure

Updating the Firmware via USB

Connect a USB device to your PC. If there is any

data in the USB device, remove it first.

Download the firmware file from the Onkyo web

site. The file name is as follows:

ONKAVR****_************.zip

Unzip the downloaded file. The following six files

are created:

ONKAVR****_************.of1

ONKAVR****_************.of2

ONKAVR****_************.of3

ONKAVR****_************.of4

ONKAVR****_************.of5

ONKAVR****_************.of6

Copy the extracted files to the USB device. Be

careful not to copy the zip file.

Remove the USB device from your PC and connect

it to the USB port on the AV receiver.

When the AV receiver has two USB ports, you can

use either one.

Make sure the AV receiver and TV are turned on.

If the AV receiver is in standby mode, press

8ON/STANDBY on the AV receiver to light up the

front display.

Select the USB input source.

“Now Initializing...” appears on the AV receiver’s

display and then the name of the USB device is

displayed. It takes 20 to 30 seconds to recognize the

USB device.

Press RECEIVER followed by HOME on the remote

controller.

The Home menu appears on the TV screen.

Select “Firmware Update” and press ENTER.

Select “Update via USB” and press ENTER.

Note that this option will not be available if there is no

firmware file newer than the currently installed

version.

Select “Update” and press ENTER.

The update process will begin.

During the update process, the on-screen display may

disappear depending on the updated program. When

this occurs, you can still view the update progress on

the AV receiver’s display. The on-screen display will

reappear after the update is complete, and upon

turning the AV receiver off and on again.

Do not turn off the AV receiver and do not remove the

USB device during the update process.

The message “Completed!” appears on the AV

receiver’s display, indicating that the update has

been completed.

Remove the USB device.

Turn off the AV receiver using 8ON/STANDBY on

the front panel.

Do not use 8RECEIVER on the remote controller.

Once turned off, the AV receiver will automatically

turn on again.

Congratulations! You now have the latest firmware

installed on your Onkyo AV receiver.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Onkyo TX-NR3010 Seite 109

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Onkyo TX-NR3010

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info