Bedienungsanleitung Onkyo TX-NR414 (Seite 44 von 128) (Englisch)

492644

Zoom out

Zoom in

Vorherige Seite

1/128

Nächste Seite

Advanced Operations

En-44

Menu Digital Audio

If you connect a component to a digital audio input, you

must assign that input to an input selector. For example, if

you connect your CD player to the OPTICAL IN 1, you

must assign “OPTICAL1” to the “TV/CD” input selector.

Here are the default assignments.

■ BD/DVD, CBL/SAT, GAME, PC, AUX, TV/CD

` COAXIAL1, COAXIAL2, OPTICAL1,

OPTICAL2:

Select the input to which the component has been

connected.

` -----:

Select if the component is connected to an analog

audio input.

Note

•When an HDMI IN is assigned to an input selector in

“HDMI Input” (➔ page 43), the same HDMI IN will be set as

a priority in this assignment. In this case, if you want to use the

coaxial or optical audio input, make the appropriate selection in

the “Audio Selector” (➔ page 47).

• Available sampling rate for PCM signals (stereo/mono) from a

digital input (optical and coaxial) are 32/44.1/48/88.2/96 kHz/16,

20, 24 bit.

Menu Sp Config

This section explains how to specify which speakers are

connected and their sizes.

For speakers with a cone diameter larger than 6-1/2 inches

(16 cm), specify Large (full band). For those with a

smaller diameter, specify Small (default crossover 100Hz).

The crossover frequency can be changed in “Crossover

(Crossover Frequency)”.

Note

• These settings are not available in either of the following cases:

– A pair of headphones is connected.

–The “Audio TV Out” setting is set to “On” (➔ page 49).

–“HDMI Ctrl (RIHD)” is set to “On” (➔ page 49) and you’re

listening through your TV speakers.

■ Subwoofer

` Yes

` No

■ Front

` Small:

` Large:

Select based on the cone diameter.

Note

• If the “Subwoofer” setting is set to “No”, this setting is fixed to

“Large”.

■ Center

, Surround

` Small:

` Large:

Select based on the cone diameter.

` None

Note

If the “Front” setting is set to “Small”, the “Large” option

cannot be selected.

■ Crossover (Crossover Frequency)

This setting is advantageous for the speakers that you

specified as “Small” in

“Sp Config (Speaker

Configuration)”

. To get the best bass performance from

your speaker system, you need to set the crossover

frequency according to the size and frequency response

of your speakers.

` 40Hz, 50Hz, 60Hz, 70Hz, 80Hz, 90Hz, 100Hz,

120Hz, 150Hz, 200Hz

Use the diameter of the smallest speaker in your system

when choosing the crossover frequency.

Choose the setting matching your speaker.

Digital Audio (Digital Audio Input)

Input selector Default assignment

BD/DVD COAXIAL1

CBL/SAT COAXIAL2

GAME OPTICAL1

PC -----

AUX - - - - -

TV/CD OPTICAL2

1 2 3 4 5

“Setup”

Sp Config (Speaker Configuration)

1 2 3 4 5

“Setup”

Cone diameter

Speaker cone diameter Crossover frequency

Over 8 in. (20 cm)

40/50/60 Hz

6-1/2 to 8 in. (16 to 20 cm)

70/80/90 Hz

5-1/4 to 6-1/2 in. (13 to 16 cm) 100 Hz

3-1/2 to 5-1/4 in. (9 to 13 cm) 120 Hz

Under 3-1/2 in. (9 cm)

150/200 Hz

To be continued

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Onkyo TX-NR414 Seite 44

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Onkyo TX-NR414

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info