Bedienungsanleitung Onkyo TX-NR807 (Seite 140 von 148) (Englisch)

553771

140

Zoom out

Zoom in

Vorherige Seite

1/148

Nächste Seite

140

Troubleshooting—Continued

There’s no picture

• Make sure that all video connecting plugs are pushed

in all the way (page 24).

• Make sure that each video component is properly con-

nected. (pages 26-40)

• If your TV is connected to the HDMI OUT, select

“- - - - -” in the “HDMI Input Setup” on page 48 to

watch composite video, S-Video, and component

video sources.

TX-NR807:

Make sure that “HDMI” is selected in the “Monitor

Out” setting.

• If the video source is connected to a component video

input, you must assign that input to an input selector

(page 49), and your TV must be connected to either

the HDMI OUT or COMPONENT VIDEO MONI-

TOR OUT (pages 26 and 30).

TX-NR807:

In the “MONITOR OUT” setting, select “HDMI” for

HDMI OUT, “Analog” for COMPONENT VIDEO

MONITOR OUT.

• If the video source is connected to an S-Video or com-

posite video input, your TV must be connected to the

HDMI OUT or the corresponding S-Video or compos-

ite video output (pages 30 and 26).

• If the video source is connected to an HDMI input,

you must assign that input to an input selector

(page 48), and your TV must be connected to the

HDMI OUT (page 26).

• While the Pure Audio listening mode is selected, the

video circuitry is turned off and only video signals

input through HDMI IN can be output.

• On your TV, make sure that the video input to which

the AV receiver is connected is selected.

There’s no picture from a source connected to

an HDMI IN

• Reliable operation with an HDMI-to-DVI adapter is

not guaranteed. In addition, video signals from a PC

are not guaranteed (page 26).

• When the “Resolution” (page 47) is set to any resolu-

tion not supported by the TV, no video is output by the

HDMI OUT.

• If the message “Resolution Error” appears on the AV

receiver’s display, this indicates that your TV does not

support the current video resolution and you need to

select another resolution on your DVD player.

The onscreen menus don’t appear

• On European, Australian and Asian models, specify

the TV system used in your area in the “TV Format

Setup” on page 52.

• On your TV, make sure that the video input to which

the AV receiver is connected is selected.

The picture is distorted

• On European, Australian and Asian models, specify

the TV system used in your area in the “TV Format

Setup” on page 52.

The immediate display does not appear

• If you select “HDMI” in the “Monitor Out” setting

(page 46), the immediate display will not appear when

the input signal from the COMPONENT VIDEO IN is

output to a device connected to the COMPONENT

VIDEO MONITOR OUT (TX-NR807).

• Depending on the input signal, the immediate display

may not appear when the input signal from the HDMI

IN is output to a device connected to the HDMI OUT.

Reception is noisy, FM stereo reception is

noisy, or the FM STEREO indicator doesn’t

appear

• Relocate your antenna.

• Move the AV receiver away from your TV or com-

puter.

• Listen to the station in mono (page 66).

• When listening to an AM station, operating the remote

controller may cause noise.

• Passing cars and airplanes can cause interference.

• Concrete walls weaken radio signals.

• If nothing improves the reception, install an outdoor

antenna.

The remote controller doesn’t work

• Make sure that the batteries are installed with the cor-

rect polarity (page 14).

• Install new batteries. Don’t mix different types of bat-

teries, or old and new batteries (page 14).

• Make sure that the remote controller is not too far

away from the AV receiver, and that there’s no

obstruction between the remote controller and the AV

receiver’s remote control sensor (page 14).

• Make sure that the AV receiver is not subjected to

direct sunshine or inverter-type fluorescent lights.

Relocate if necessary.

• If the AV receiver is installed in a rack or cabinet with

colored-glass doors, the remote controller may not

work reliably when the doors are closed.

• Make sure you’ve selected the correct remote control-

ler mode (pages 15 and 127-133).

• When using the remote controller to control other

manufacturers’ AV components, some buttons may

not work as expected.

• Make sure you’ve entered the correct remote control

code (page 125).

• Make sure to set the same ID on both the AV receiver

and remote controller (page 100).

Video

Tuner

Remote Controller

TX-NR807_En.book Page 140 Tuesday, July 28, 2009 12:00 PM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Onkyo TX-NR807 Seite 140

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Onkyo TX-NR807

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info