Bedienungsanleitung Onkyo TX-NR828 (Seite 28 von 152) (Englisch)

527521

Zoom out

Zoom in

Vorherige Seite

1/152

Nächste Seite

Turning On & Basic Operations

En-28

Turn on the AV receiver and the connected TV.

On the TV, select the input to which the AV

receiver is connected.

Set the speaker setup microphone at the Main

Listening Position a, and connect it to the

SETUP MIC jack.

The speaker setting menu appears.

Note

• The on-screen menus appear only on a TV that is

connected to HDMI OUT MAIN. If your TV is

connected to other video outputs, use the AV

receiver’s display when changing settings.

When you’ve finished making the settings,

press ENTER.

Perform the “2. Speaker Setup” according to your

speaker configuration:

– Speakers Type(Front) (➔ page 64)

– Powered Zone 2 (➔ page 64)

– Subwoofer (➔ page 64)

If you use a powered subwoofer(s), go to step 4.

If not, go to step 5.

Speaker setup microphone

SETUP MIC jack

MultEQ: Auto Setup

AUDYSSEY

Speakers Type(Front)

Powered Zone 2

Subwoofer

Normal

Yes

Adjust the subwoofer volume level to 75 dB,

and then press ENTER.

Test tones are played through the subwoofer.

Use the volume control on the subwoofer.

Note

• If your subwoofer does not have a volume control,

disregard the displayed level and press ENTER to

proceed to the next step.

• If you set the subwoofer’s volume control to its

maximum and the level displayed is lower than 75 dB,

leave the subwoofer’s volume control at its maximum

and press ENTER to proceed to the next step.

Use q/w to select “Audyssey Quick Start” or

“Audyssey MultEQ Full Calibration”, and then

press ENTER.

Press ENTER.

Audyssey MultEQ

Room Correction and

Speaker Setup starts.

Test tones are played through each speaker as

Audyssey MultEQ Room Correction and Speaker

Setup runs. This process takes a few minutes.

Please refrain from talking during

measurements and do not stand between

speakers and the microphone.

Do not disconnect the speaker setup microphone

during Audyssey MultEQ Room Correction and

Speaker Setup, unless you want to cancel the

setup.

If you select “Audyssey Quick Start”, you will go

to step 9.

Place the speaker setup microphone at the

next position, and then press ENTER.

Audyssey MultEQ performs more

measurements. This takes a few minutes.

When prompted, repeat step 7.

Use q/w to select an option, and then press

ENTER.

The options are:

` Save:

Save the calculated settings and exit

Audyssey MultEQ Room Correction and

Speaker Setup.

` Cancel:

Cancel Audyssey MultEQ Room Correction

and Speaker Setup.

Tip

• You can view the calculated settings for the speaker

configuration, speaker distances, and speaker levels

by using e/r.

Use q/w to select a target, and use e/r to

change the setting.

After the results of Audyssey MultEQ have been

saved, the menu will display the “Audyssey”

(➔ page 68), “Dynamic EQ” (➔ page 69),

“Dynamic Volume” (➔ page 69) settings.

Note

• When “Audyssey Quick Start” has been used for

measurement, “Audyssey” cannot be selected.

• These settings are applied to all input selectors.

Press ENTER.

Disconnect the speaker setup microphone.

Save

Cancel

AUDYSSEY

MultEQ: Auto Setup

-- Review Speaker Configuration --

Subwoofer

Front

Center

Surround

Front Wide

Front High

Surround Back

Surround Back Ch

Yes

100Hz

40Hz

100Hz

None

120Hz

2ch

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Onkyo TX-NR828 Seite 28

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Onkyo TX-NR828

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info