Bedienungsanleitung Onkyo TX-NR828 (Seite 29 von 152) (Englisch)

527521

Zoom out

Zoom in

Vorherige Seite

1/152

Nächste Seite

Turning On & Basic Operations

En-29

Note

• You can cancel Audyssey MultEQ

Room Correction and

Speaker Setup at any point in this procedure simply by

disconnecting the setup microphone.

• Do not connect or disconnect any speakers during

Audyssey MultEQ Room Correction and Speaker Setup.

• If the AV receiver is muted, it will be unmuted automatically

when Audyssey MultEQ Room Correction and Speaker

Setup starts.

• Changes to the room after Audyssey MultEQ Room

Correction and Speaker Setup requires you run

Audyssey MultEQ Room Correction and Speaker Setup

again, as room EQ characteristics may have changed.

Error Messages

While Audyssey MultEQ Room Correction and

Speaker Setup is in progress, one of the error

messages below may appear.

The options are:

` Retry:

Try again.

` Cancel:

Cancel Audyssey MultEQ Room Correction and

Speaker Setup.

• Ambient noise is too high.

The background noise is too loud. Remove the

source of the noise and try again.

• Speaker Matching Error!

The number of speakers detected was different

from that of the first measurement. Check the

speaker connection.

• Writing Error!

This message appears if saving fails. Try saving

again. If this message appears after 2 or 3

attempts, contact your Onkyo dealer.

• Speaker Detect Error

This message appears if a speaker is not detected.

“No” means that no speaker was detected.

Tip

• See “Speaker Configuration” for appropriate settings

(➔ page 14).

Note

• Please note that THX recommends any THX main

speakers be set to “80Hz(THX)”. If you set up your

speakers using Audyssey MultEQ Room Correction and

Speaker Setup, please make sure manually that any THX

speakers are set to “80Hz(THX)” crossover (➔ page 64).

• Sometimes due to the electrical complexities of subwoofers

and the interaction with the room, THX recommends setting

the level and the distance of the subwoofer manually.

• Sometimes due to interaction with the room, you may

notice irregular results when setting the level and/or

distance of the main speakers. If this happens, THX

recommends setting them manually.

Using a Powered Subwoofer

If you’re using a powered subwoofer and it outputs

very low-frequency sound at a low volume level, it

may not be detected by Audyssey MultEQ Room

Correction and Speaker Setup.

If the “Subwoofer” appears on the “Review Speaker

Configuration” screen as “No”, increase the

subwoofer’s volume to the half-way point, set it to its

highest crossover frequency, and then try running

Audyssey MultEQ Room Correction and Speaker

Setup again. Note that if the volume is set too high

and the sound distorts, detection issues may occur,

so use an appropriate volume level. If the subwoofer

has a low-pass filter switch, set it to Off or Direct.

Refer to your subwoofer’s instruction manual for

details.

Retry

Cancel

Ambient noise is too high.

AUDYSSEY

MultEQ: Auto Setup

Error message

The setup of the speaker can be done manually

(➔ page 64).

The setup of the volume level of each speaker also

can be done manually (➔ page 65).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Onkyo TX-NR828 Seite 29

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Onkyo TX-NR828

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info