Bedienungsanleitung Onkyo TX-NR828 (Seite 64 von 152) (Englisch)

527521

Zoom out

Zoom in

Vorherige Seite

1/152

Nächste Seite

Advanced Operations

En-64

Operating

procedure

(➔ page 60)

■ Speakers Type(Front)

` Normal

Select this if you’ve connected your front

speakers normally.

` Bi-Amp:

Select this if you’ve bi-amped your front

speakers.

■ Powered Zone 2

` No

` Yes:

Zone 2 speakers can be used (Powered Zone 2

enabled).

Note

• If the “Speakers Type(Front)” setting is set to “Bi-Amp”,

Powered Zone 2 cannot be used.

• When the “Powered Zone 2” setting is set to “Yes” and

Zone 2 is turned on, the surround back and front high

speakers cannot be used.

Speaker Configuration

With these settings, you can specify which speakers

are connected and a crossover frequency for each

speaker. Specify “Full Band” for speakers that can

output low frequency bass sounds adequately, for

example, speakers with a good sized woofer. For

smaller speakers, specify a crossover frequency.

Sounds below the crossover frequency will be output

by the subwoofer instead of the speaker. Refer to

your speaker’s manuals to determine the optimum

crossover frequencies. If you set up your speakers

using Audyssey MultEQ Room Correction and

Speaker Setup, please make sure manually that any

THX speakers are set to “80Hz(THX)” crossover.

■ Subwoofer

` Yes

` No

■ Front

` Full Band

` 40Hz to 80Hz(THX)

to 100Hz, 120Hz, 150Hz,

200Hz

Note

• If the “Subwoofer” setting is set to “No”, the “Front” setting

is fixed at “Full Band”.

■ Center

, Surround

` Full Band

` 40Hz to 80Hz(THX)

to 100Hz, 120Hz, 150Hz,

200Hz

` None

■ Front Wide

*1*2*4

, Front High

*1*2*3

` Full Band

` 40Hz to 80Hz(THX) to 100Hz, 120Hz, 150Hz,

200Hz

` None

■ Surround Back

*1*2*3

` Full Band

` 40Hz to 80Hz(THX)

to 100Hz, 120Hz, 150Hz,

200Hz

` None

Note

“Full Band” can be selected only when “Full Band” is

selected in the “Front” setting.

If the “Surround” setting is set to “None”, this setting

cannot be selected.

If the “Speakers Type(Front)” setting is set to “Bi-Amp”,

or the “Powered Zone 2” setting is set to “Yes” together

with Zone 2 turned on, this setting cannot be selected.

If the “Speakers Type(Front)” setting is set to “Bi-Amp”,

or the “Powered Zone 2” setting is set to “Yes”, this

setting cannot be selected.

■ Surround Back Ch

` 1ch:

Select if only one surround back speaker L is

connected.

` 2ch

Select if two (left and right) surround back

speakers are connected.

Note

• If the “Surround Back” setting is set to “None”, this setting

cannot be selected.

■ LPF of LFE

(Low-Pass Filter for the LFE Channel)

` 80Hz, 90Hz, 100Hz, 120Hz

` Off:

Low-Pass Filter is not applied.

With this setting, you can specify the cutoff

frequency of the LFE channel’s low-pass filter

(LPF), which can be used to filter out unwanted

hum. The LPF only applies to sources that use the

LFE channel.

Note

• If you’re using THX-certified speakers, select “80Hz”.

■ Subwoofer Phase

` 0

` 180º:

Moves the subwoofer phase.

Note

• If the “Subwoofer” setting is set to “No”, this setting cannot

be selected.

This setting is set automatically by

Audyssey MultEQ

Room Correction and Speaker

Setup function (➔ page 27).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Onkyo TX-NR828 Seite 64

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Onkyo TX-NR828

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info