Bedienungsanleitung Onkyo TX-NR828 (Seite 81 von 152) (Englisch)

527521

Zoom out

Zoom in

Vorherige Seite

1/152

Nächste Seite

Advanced Operations

En-81

Muting Zone 2

■ Operating on the remote controller

Tip

• To unmute, press ZONE followed by MUTING again.

Zone 2 can also be unmuted by adjusting the volume.

Note

• Only analog, NET or USB input source is output from the

ZONE 2/ZONE 3 LINE OUT jacks and ZONE 2 L/R

terminals.

• You cannot select different AM or FM radio stations for your

main room and Zone 2/3. The same AM/FM radio station

will be heard in each room. Namely, if you have selected an

FM station for the main room, that station will also be output

in Zone 2/3.

• You cannot select different input selector NET or USB for

your main room and Zone 2/3. Namely, if you have selected

USB input selector for Zone 2/3, USB input selector will be

selected in main room even if NET has been selected for

main room.

• BLUETOOTH cannot be selected as input selector in Multi

Zone. If you play audio from Bluetooth-enabled device in

Multi Zone, select “Zone 2 Selector: Source” or “Zone 3

Selector: Source”, and BLUETOOTH as input selector in

Main room.

• When Zone 2/3 is activated and its input selector is

selected, the power consumption of standby mode slightly

increases.

• While Zone 2/3 is on, u functions will not work.

• When setting the AV receiver to standby mode while Zone

2/3 is active, the Z2 or Z3 indicator is dimly lit.

• Activating Zones in the main room when the listening mode

is set to Pure Audio will automatically switch it to Direct.

•“GAME2” cannot be selected as input sources for Zone 2/3.

• When “GAME2” is the input source of Main room and

Zone 2/3 is set to share the same source, no sound will be

output from Zone 2/3.

• Even if you repeatedly press the remote controller’s ZONE

to select zones, the last zone selection will be retained once

you have switched to other components by pressing other

REMOTE MODE after pressing ZONE.

To control the AV receiver with the remote controller

while you’re in Zone, you’ll need a commercially

available multiroom remote control kit for each zone.

• Multiroom kits are made by Niles and Xantech.

These kits can also be used when there isn’t a clear

line of sight to the AV receiver’s remote sensor, such

as when it’s installed inside a cabinet.

Using a Multiroom Kit with Zone

In this setup, the IR receiver in Zone picks up the

infrared signals from the remote controller and feeds

them through to the AV receiver in the main room via

the connecting block.

The miniplug cable from the connecting block should

be connected to the AV receiver’s IR IN jack, as

shown below.

Using a Multiroom Kit with a Cabinet

In this setup, the IR receiver picks up the infrared

signals from the remote controller and feeds them to

the AV receiver located in the cabinet via the

connecting block.

Press ZONE repeatedly to select Zone 2, and

then press MUTING.

Using the Remote Controller in

Zone and Multiroom Control Kits

IR IN

Connecting

block

Remote controller

receiver

Main room Zone

Signal flow

From the connecting block

Miniplug cable

AV receiver

Signal flow

IR IN

Connecting

block

Remote controller

receiver

Inside

cabinet

Signal flow

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Onkyo TX-NR828 Seite 81

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Onkyo TX-NR828

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info