Bedienungsanleitung Onkyo TX-NR828 (Seite 83 von 152) (Englisch)

527521

Zoom out

Zoom in

Vorherige Seite

1/152

Nächste Seite

Controlling Other Components

En-83

Note

• Though the provided remote control codes are correct at

the time of release, they are subject to change.

You can change the configuration of colored buttons,

with which REMOTE MODE buttons are preset.

Tip

• To reset the REMOTE MODE buttons to their default

settings, see “Resetting the REMOTE MODE Buttons”.

Note

• If any other button than the colored buttons is pressed, the

operation will be cancelled.

• This operation cannot be done while the AV receiver is in

Receiver mode or when Zone 2/3 is active.

Onkyo components that are connected via u are

controlled by pointing the remote controller at the AV

receiver, not the component. This allows you to

control components that are out of view, in a rack, for

example.

Controlling Onkyo components without u

If you want to control an Onkyo component by

pointing the remote controller directly at it, or you

want to control an Onkyo component that’s not

connected via u, use the following remote control

codes:

` 30627:

Onkyo DVD player without u

` 71817:

Onkyo CD player without u

` 32900/33100/33500:

Onkyo Blu-ray Disc player

` 32901/33104/33504:

Onkyo HD DVD player

` 70868:

Onkyo MD recorder without u

` 71323:

Onkyo CD recorder without u

` 82990:

Onkyo Dock without u

You can reset a REMOTE MODE button to its default

remote control code.

Within 30 seconds, use the number buttons to

enter the 5-digit remote control code.

The REMOTE MODE button flashes twice.

If the remote control code is not entered

successfully, the REMOTE MODE button will

flash once slowly.

Remapping Colored Buttons

While holding down the REMOTE MODE

button that you want to program, press and

hold down A (Red) until the REMOTE MODE

button lights (about 3 seconds).

You can only change colored buttons for

components whose codes belong to categories

of the Remote Control Codes list (BD/DVD

player, TV, cable set-top box, etc).

Within 30 seconds, press the colored buttons

in the order that you want to reassign them.

The button presses are assigned to each button

from left to right. The REMOTE MODE button

flashes twice, indicating that the sequence has

been successfully assigned. If the sequence is

not successfully assigned, the REMOTE MODE

button will flash once slowly.

Remote Control Codes for Onkyo

Components Connected via RI

Make sure the Onkyo component is connected

with an u cable and an analog audio cable

(RCA).

See “Connecting Onkyo RI Components” for

details (➔ page 23).

Enter the appropriate remote control code for

a REMOTE MODE button, by referring to the

previous section.

` 42157:

Onkyo cassette tape deck with u

` 81993:

Onkyo Dock with u

Press the REMOTE MODE button, point the

remote controller at the AV receiver, and

operate the component.

Resetting the REMOTE MODE Buttons

While holding down the REMOTE MODE

button that you want to reset, press and hold

down HOME until the REMOTE MODE button

lights (about 3 seconds).

Within 30 seconds, press the REMOTE MODE

button again.

The REMOTE MODE button flashes twice,

indicating that the button has been reset.

Each REMOTE MODE button is preprogrammed

with a remote control code. When a button is

reset, its preprogrammed code is restored.

Note

• The learning command is also reset.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Onkyo TX-NR828 Seite 83

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Onkyo TX-NR828

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info