Bedienungsanleitung Onkyo TX-NR906 (Seite 95 von 150) (Englisch)

62439

Zoom out

Zoom in

Vorherige Seite

1/150

Nächste Seite

Advanced Setup—Continued

This section explains items on the “Speaker Setup”

menu.

Some of the speaker settings are set automatically by the

Automatic Speaker Setup function (see page 64).

Speaker Settings

See “Speaker Settings” on page 61.

Speaker Configuration

With the Speaker Configuration settings, you can specify

which speakers are connected and a crossover frequency,

distance, and level for each speaker.

You can choose which of the speakers you want to use

with the Speakers A and Speakers B configurations, and

set the crossover frequencies, distances, and levels of the

front Speakers A and front Speakers B independently.

The other speakers (i.e., subwoofer, center, surround,

and surround back) use the same crossover frequencies,

distances, and levels for Speakers A and Speakers B.

The following crossover frequencies can be specified:

Full Band, 40 Hz, 50 Hz, 60 Hz, 70 Hz, 80 Hz (THX),

90 Hz, 100 Hz, 110 Hz, 120 Hz, 130 Hz, 150 Hz, or

200 Hz.

Specify Full Band for speakers that can output low-fre-

quency bass sounds adequately, for example, speakers

with a good sized woofer. For smaller speakers, specify

a crossover frequency. Sounds below the crossover fre-

quency will then be output by the subwoofer instead of

the speaker. Refer to your speakers’ manuals to deter-

mine the optimum crossover frequencies.

If you’re using THX-certified speakers, specify

80 Hz (THX) for all speakers.

Speaker Setup

INPUT SELECTOR

LISTENING MODE

DISPLAY MUTING

DIMMER

CDR/MD/DOCK

SAT

TAPE/AMP

SLEEP

MACRO

REMOTE MODE

SUBTITLE

AUDIO

REPEAT

PLAY MODE

---

10 11 12

PLAYLIST

RANDOMREC

ENTER

SURR

DIRECT

THX

PURE A

STEREO

ALL ST

VOL

DISC

ALBUM

VCR

CABLE

NET/USB

DVD

RECEIVER

123

ZONE

SP A SP B

1, 5

2-4

*TX-NR906 only

These settings are set automatically by the Automatic

Speaker Setup function (see page 64).

Press the [RECEIVER] REMOTE

MODE button, and then use the

remote controller’s [SP A] or

[SP B] button to select Speakers

A or Speakers B, respectively

(TX-NR906 only).

Note:

• Speakers B cannot be selected if

“Speaker Type: Front(Speaker B)” is

set to “Not Use”.

• TX-SR876 continue with step 2 after

press the [RECEIVER] REMOTE

MODE button.

Press the [SETUP] button.

The main menu appears onscreen.

Use the Up and Down [q]/[w] but-

tons to select “2. Speaker

Setup”, and then press [ENTER].

The “Speaker Setup” menu appears.

Use the Up and Down [q]/[w] but-

tons to select “2. Speaker Con-

fig”, and then press [ENTER].

The “Speaker Config” screen appears.

2. Speaker Setup

1. Speaker Settings

2. Speaker Config

3. Speaker Distance

4. Level Calibration

5. Equalizer Settings

6. THX Audio Setup

MOVE ENTER RETURN

ENTER

RETURN

EXIT

SETUP

RETURN

EXIT

SETUP

MOVE VAL U E

2–2. Speaker Config

Subwoofer

Front

Center

Surround

SurrBack

SurrBack Ch

LPF of LFE

DoubleBass

Yes

Full Band

100Hz

2ch

120Hz

Speaker A

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Onkyo TX-NR906 Seite 95

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Onkyo TX-NR906

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info