Bedienungsanleitung Onkyo TX-NR906 (Seite 96 von 150) (Englisch)

62439

Zoom out

Zoom in

Vorherige Seite

1/150

Nächste Seite

Advanced Setup—Continued

Use the Up and Down [q]/[w] but-

tons to select “Subwoofer”, and

then use the Left and Right

[e]/[r] buttons to select:

Yes: Select if a subwoofer is con-

nected.

No: Select if no subwoofer is con-

nected.

Note:

The same setting is used for Speakers A

and Speakers B.

Use the Up and Down [q]/[w] but-

tons to select “Front”, and then

use the Left and Right [e]/[r]

buttons to select a crossover fre-

quency.

Notes:

• This setting can be set independently

for front Speakers A and front

Speakers B.

• Fixed at “Full Band” if “Subwoofer”

(step 5) is set to “No”.

Use the Up and Down [q]/[w] but-

tons to select “Center”, and then

use the Left and Right [e]/[r]

buttons to select a crossover fre-

quency.

If no center speaker is connected, select

None.

Notes:

• The same setting is used for Speakers

A and Speakers B.

• Can be set if the currently selected

speakers (Speakers A or Speakers B)

is set to “BTL” (page 61).

• Cannot select “Full Band” if “Front”

(step 6) is set to anything other than

“Full Band”.

• For Speakers B, if any channel is set

to “Full Band”, “Center” is fixed at

“Full Band”.

Use the Up and Down [q]/[w] but-

tons to select “Surround”, and

then use the Left and Right

[e]/[r] buttons to select a cross-

over frequency.

If no surround left and right speakers

are connected, select “None”.

Notes:

• The same setting is used for Speakers

A and Speakers B.

• Can be set if the currently selected

speakers (Speakers A or Speakers B)

is set to “BTL” (page 61).

• Cannot select “Full Band” if “Front”

(step 6) is set to anything other than

“Full Band”.

Use the Up and Down [q]/[w] but-

tons to select “SurrBack”, and

then use the Left and Right

[e]/[r] buttons to select a cross-

over frequency.

If no surround back speakers are con-

nected, select “None”.

Notes:

• The same setting is used for Speakers

A and Speakers B.

• Cannot be set if “Speaker Type:

Front(Speaker A) or Front(Speaker

B)” is set to “Bi-Amp” or “BTL”

(page 61), “Surround” is set to

“None” (step 8), or “Powered

Zone2” is being used (page 132).

• Cannot select “Full Band” if “Sur-

round” (step 8) is set to anything

other than “Full Band”.

Use the Up and Down [q]/[w] but-

tons to select “SurrBack Ch”,

and then use the Left and Right

[e]/[r] buttons to select:

1ch: Select if one surround back

speaker is connected.

2ch: Select if two (left and right)

surround back speakers are

connected.

Notes:

• The same setting is used for Speakers

A and Speakers B.

• Cannot be set if “Speaker Type:

Front(Speaker A) or Front(Speaker

B)” is set to “Bi-Amp” or “BTL”

(page 61), “SurrBack” is set to

“None” (step 9), or “Powered

Zone2” is being used (page 132).

Continue with step 11 on the next page.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Onkyo TX-NR906 Seite 96

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Onkyo TX-NR906

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info